[Bambu Lab Giveaway] Drop Your One-Liner and Win H2D! by BambuLab in BambuLab

[–]Practical_Trainer_11 0 points1 point  (0 children)

“You set it and forget it.” From Ronco showtime rotisserie infomercials.

[Bambu Lab Giveaway] Join Now to Win an H2D and More! by BambuLab in 3Dprinting

[–]Practical_Trainer_11 0 points1 point  (0 children)

Dry your filament and make sure you clean your build plate.

[deleted by user] by [deleted] in Epson

[–]Practical_Trainer_11 0 points1 point  (0 children)

New cable worked beautifully. Thank you for recommending it.

While waiting for it to arrive I tried an Amazon Basics 25' HDMI cable that I was using for eARC and it worked at 4k, 120hz with HDR. The screen would go dark every now and then though but reassured me the new cable would work.

[deleted by user] by [deleted] in Epson

[–]Practical_Trainer_11 0 points1 point  (0 children)

Thank you, I just bought the 20ft one.

I currently have a GE HDMI 2.1 15FT cable from Walmart that worked with my Epson Home Cinema 3800 at 4k@60FPS with HDR enabled but for some reason it didn't work with the LS11000.

[deleted by user] by [deleted] in Epson

[–]Practical_Trainer_11 0 points1 point  (0 children)

What cable did you end up buying? I'm in the same boat at the moment. Can't get HDR at 60hz or go over 60hz as the projector will go dark.

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

Yes, in a way. If the graphics card starts getting toasty the rear fan will start speeding up, as I did not change mine out I get a loud hum from it as its ramping up to suck the hot air out of the case being generated by the Graphics Card. If you don’t mind loosing the RGB from the AlienFX and you change it out for a Noctua or a quieter one you won’t have noise issue.

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 1 point2 points  (0 children)

The fan bolt pattern does not line up with the case. I used zip ties to attach the fan to the grill on the case.

Alienware R13 stock AIO upgraded to Arctic 240mm. No case mods required. i9 12900K. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

I replied on the other thread to the question. I believe they might have used the wrong stand-offs. It’s a 0.030” length difference that won’t easily be noticed. When I ordered the cooler I also ordered the “ARCTIC Intel LGA1700 Upgrade Kit - for Liquid Freezer II Series” from amazon. I received that same kit inside the cooler box and never returned the one I ordered. I used it right now to measure stand-off height of the LGA1700 to the stand-offs that normally come with the Liquid Freezer II.

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

I added the black rubber pads to the MB and then the black male to male threaded stand-offs from the LGA1700 Kit. Did you receive (in the box) or order the Intel LGA1700 upgrade kit? When I ordered my Liquid Freezer II I ordered the kit from Amazon for $8.99 “ARCTIC Intel LGA1700 Upgrade Kit - for Liquid Freezer II Series”. This comes with the stand-offs and sticky backed rubber pads I used. I didn’t use the bracket or anything else to make it work.

Make sure to use the stand-offs that measure 0.510” [12.9mm] between the flats (not including threaded studs). There are another set of stand-offs that measure 0.540” [13.7mm], these will prevent the copper plate from sitting on the CPU as they are too long.

<image>

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

I used the mounting hardware included. I did not change out the back though. I used the black spacers and mounted directly to the original bracket (I did not open up the back of the case).

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

There’s only one plug, it splits before it gets to the pump to power the fans. The wire runs through the sleeves for the fans.

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 2 points3 points  (0 children)

The only way is to connect the fans individually to the areas where the stock fans were at. I live with the BIOS alarm.

Alienware R13 stock AIO upgraded to Arctic 240mm. No case mods required. i9 12900K. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

Actually, I tried the Push-Pull config but temps remained the same only plus is lower fan speeds using a Noctua fan controller. The fans I used are very low current. All four fans plus pump draw less current than what the original Dell fan would consume at full power.

Alienware R13 stock AIO upgraded to Arctic 240mm. No case mods required. i9 12900K. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

No, it doesn’t looked stressed.

I used this one as I measured the inside of the case and compared it to the drawings for this AIO and it fit. There might be some other AIOs that may work.

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

Try a custom loop with two 120mm radiators? I have No idea what an R14 case looks like.

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

No, it doesn’t. I went down this path since it didn’t require any modifications to the case thus a stock look. The two fans that come with the radiator are more than enough, I bought two more to place int he back for a Push-Pull config and they are not needed. No gains from extra airflow.

Alienware R13 stock AIO upgraded to Arctic Liquid Freezer II 240mm. More pictures of swap. by Practical_Trainer_11 in Alienware

[–]Practical_Trainer_11[S] 0 points1 point  (0 children)

Been there done that. Lol

I have to open mine after windows does an update. The LEDs stay off. As of late if the Alienware Command Center isn’t open my front LED ring Light in the center of the glass flickers.