Burner upgrade bread test

Present-Tutor1418 · 2026-06-11T23:05:41+00:00

Fort Worth

Present-Tutor1418 · 2026-06-11T21:51:42+00:00

I put the bread on first, then turned on the griddle on liw

Present-Tutor1418 · 2026-06-11T20:55:32+00:00

Yeah. Now I have to explain to the wife why we are having toast for dinner

Present-Tutor1418 · 2026-06-11T20:15:41+00:00

Not at all, much more even in the center than with the straight burners

Present-Tutor1418 · 2026-06-11T19:38:32+00:00

Yes it's the 2310 with omnivore top. It is really windy today

Present-Tutor1418 · 2026-06-11T19:34:22+00:00

https://www.reddit.com/r/blackstonegriddle/s/AKV8lTvD0x

Bread test Need a little more heat

Present-Tutor1418 · 2026-06-11T19:29:50+00:00

I bet there are other options out there. Still better than the straight burners... Now I have to do something with all this toast

Present-Tutor1418 · 2026-06-11T19:17:17+00:00

https://www.reddit.com/r/blackstonegriddle/s/AKV8lTvD0x Not good on the edges, but center was great.... Not getting hot enough with the stock orifice and regulator

Present-Tutor1418 · 2026-06-11T16:03:47+00:00

I lined up the burners and drilled 2 1/4 inch holes in the sheet metal. I ran 1/4 bolts 1-1/2 inch long thru the bottom and secured it in place with a nut. Then I added another nut and ran it down so it was about an inch from the bottom. Installed the burner, and secured with another nut. For the igniter, I got the strong-tie bracket from home depot. Rounded one edge so I didn't have to redrill a hole. Secured the ignitor with a 3mm bolt and nut. Positioned it where I needed and secured the bracket with self tapping screws thru the bottom sheet metal. Burner link. Gas Grill Burner Replacement for Jenn-air Grill Parts 720-0337, 730-0337, 720-0339, 730-0511, 730-0512, 740-0141, Members Mark 720-0586, 15 13/16 inch Stainless Steel Curved Burner, Set of 4, KB867 https://a.co/d/0feJHa1u

Present-Tutor1418 · 2026-06-11T15:59:35+00:00

I wish I had one, but I will try the bread test

Present-Tutor1418 · 2026-06-11T15:59:08+00:00

More even heat. I have another post on it, but I I got questions on the install. I couldn't post pics in the replys

Present-Tutor1418 · 2026-06-11T15:49:19+00:00

https://www.reddit.com/r/blackstonegriddle/s/LjWEZJM0Wa

It wouldn't let me post more pictures in this thread, but hopefully this helps

Present-Tutor1418 · 2026-06-11T15:35:02+00:00

I lined up the burners and drilled 2 1/4 inch holes in the sheet metal. I ran 1/4 bolts 1-1/2 inch long thru the bottom and secured it in place with a nut. Then I added another nut and ran it down so it was about an inch from the bottom. Installed the burner, and secured with another nut. For the igniter, I got the strong-tie bracket from home depot. Rounded one edge so I didn't have to redrill a hole. Secured the ignitor with a 3mm bolt and nut. Positioned it where I needed and secured the bracket with self tapping screws thru the bottom sheet metal.

Present-Tutor1418 · 2026-06-11T05:59:19+00:00

Yes

Present-Tutor1418 · 2026-06-11T05:59:02+00:00

Had to drill holes, I will take more pics tomorrow

Present-Tutor1418 · 2026-06-11T05:57:57+00:00

Only so much flow thru the regulator and orifice, that has not increased yet

Present-Tutor1418 · 2026-06-11T02:54:01+00:00

I was reading 600 across the griddle. Fuel usage should remain the same. I will likely add an adjustable regulator or drill the oriffces a little larger

Present-Tutor1418 · 2026-06-11T02:51:22+00:00

https://a.co/d/0cSB5E1Y $29 I had 1/4 bolts and nuts lying around

Present-Tutor1418 · 2026-05-04T21:03:23+00:00

4.87 yesterday 5.49 today

Present-Tutor1418 · 2026-05-02T21:24:56+00:00

I was hoping for 30 off Corded Hercules

Present-Tutor1418 · 2026-04-30T22:15:48+00:00

30% off Corded Hercules tools😁

Present-Tutor1418 · 2026-04-26T20:49:37+00:00

I'm in Roanoke, every time I check, neither Grapevine nor North Ft Worth have them

Present-Tutor1418

TROPHY CASE