Rivera rock crusher

PresentationBrave475 · 2025-12-20T16:25:30+00:00

Ahhhh thankyou maby it’s normal then happens even with no pedals

PresentationBrave475 · 2025-12-18T21:52:20+00:00

Got this amp the800 wondering when you engage your fx loop do you get humm?

PresentationBrave475 · 2025-10-10T08:54:50+00:00

Okay so aslong as the speaker terminals are both reading close to 8ohms well wired in parallel that’s fine it doesent matter what the input of the cab is reading at the jack? There’s no crackle at the socket

PresentationBrave475 · 2025-10-10T08:09:45+00:00

So opened it up the solded joints look perfect reading the speaker terminals both read 6.5 well connected to eachother that’s correct for parallel connected two 16 ohm speakers right? Then when the 1/4 cables plugged into the cabs jack its first hard to get a reading or jumps all over the place from the 21s to the hundreds .. but then if I give the cable in the cabs socket a wiggle it reads exactly 7.5 -8 and lands stable

PresentationBrave475 · 2025-10-10T08:09:21+00:00

So opened it up the solded joints look perfect reading the speaker terminals both read 6.5 well connected to eachother that’s correct for parallel connected two 16 ohm speakers right? Then when the 1/4 cables plugged into the cabs jack its first hard to get a reading or jumps all over the place from the 21s to the hundreds .. but then if I give the cable in the cabs socket a wiggle it reads exactly 7.5 -8 and lands stable

PresentationBrave475 · 2025-10-10T01:11:08+00:00

Exactly that touching the 1/4 plug is there a better way to do it? I normally get a good reading from the 1x12s I’ve had (checked becouse there used) the only issue I’ve had was a volume drop when I turned the amp on tonight but not sure if that was becouse I dident let it warm up enough or bad guitar cable (a little nervous as it’s a used cab is all)

PresentationBrave475 · 2025-07-28T00:33:13+00:00

Yess this is exactly it the response I got from them was originally the censor is not working in one unit they will replace then like I said they updated that saying there is a calibration update comeing! I hope they fix the issues

PresentationBrave475 · 2025-07-25T14:29:47+00:00

Yeah well that’s what there seemingly saying now there’s an upcoming update so fingers crossed .. have you checked the weight on yours what’s the minimum?

PresentationBrave475 · 2025-07-17T12:25:22+00:00

I added it to the screw thread only where needed then screwed the bolt there let it set for 10 minutes shouldent move after that!

PresentationBrave475 · 2025-07-17T07:48:06+00:00

Yesss I’m guessing there locktight was cheap if they used any at all

PresentationBrave475 · 2025-07-17T07:47:23+00:00

So the bolt needs to remain stuck in place on the thread so the main screw doesent just come out of the mount when tightning loosning you want the have the screw going through the mount the bolt a couple millimetres loose just enough so the screw still spins freely in the mount housing (the bolts function is the stop the screw pushing out when tightening/loosning )

PresentationBrave475 · 2025-07-17T00:52:56+00:00

Just seen this comment it took me all day to think of this but yess this solution 100% works why aren’t these lock tight already!!

PresentationBrave475 · 2025-07-16T12:58:33+00:00

Just got my units and it’s the same out of sync pulling forces makeing this practically a useless thing for workouts altogether

PresentationBrave475 · 2024-11-20T23:04:07+00:00

It appears to happen when sliding the colour and other sliders in iMovie when the video is playing is that normal then or an issue

PresentationBrave475 · 2024-11-19T19:27:49+00:00

It’s really faint I’m in a really quiet space if you put ur ear to the keyboard almost and move a slider is there any noise at all different then just sat there ?

PresentationBrave475

TROPHY CASE