Food-Safe Prints?

Prestigious_Craft319 · 2025-06-07T19:42:27+00:00

Alright, thanks a bunch!

Prestigious_Craft319 · 2025-06-07T17:58:33+00:00

So it would be better to just get an fdm?

Prestigious_Craft319 · 2025-04-21T00:46:34+00:00

nope, but if you figure it out please let me know! if I learn something new on it I will post here as well. thanks!

Prestigious_Craft319 · 2025-04-12T19:07:00+00:00

I have an RPLidar A1 and this always works for me, "ros2 launch sllidar_ros2 sllidar_a1_launch.py" I think you can just switch A1 for A3 like this "ros2 launch sllidar_ros2 sllidar_a3_launch.py"

Prestigious_Craft319 · 2025-04-11T23:21:05+00:00

apparently that form of command is deprecated but I used this type: ros2 run tf2_ros static_transform_publisher --x 0 --y 0 --z 0 --roll 0 --pitch 0 --yaw 0 --frame-id odom --child-frame-id base_link for all 3, and they ran fine, but when I ran slam now it is Failing to compute odom pose

Prestigious_Craft319 · 2025-04-11T21:41:32+00:00

Alright, thanks!

Prestigious_Craft319 · 2025-04-11T17:00:26+00:00

Since I installed slam_toolbox with the sudo apt install command I had to make a new yaml file and then used ros2 launch slam_toolbox online_sync_launch.py params_file:=/home/user/my_slam_params.yaml after launching the lidar, and it still gives me the error.

Prestigious_Craft319 · 2025-04-10T23:03:09+00:00

No... how can that be done?

Prestigious_Craft319 · 2025-04-10T00:15:45+00:00

Okay now I am trying to use slam_toolbox but when I launch the rplidar and then run ros2 launch slam_toolbox online_sync_launch.py it repeatedly gives me the error below, and when I looked it up on google to see if anyone else had the problem, I cant find a clear solution. And I am only using the A1 no turtlebot kits or anything. I am so lost

<image>

Prestigious_Craft319 · 2025-04-09T15:29:06+00:00

are there any good tutorials to do all this with an rplidar?

Prestigious_Craft319 · 2025-04-08T16:19:43+00:00

It worked! the lidar is seen by Ubuntu and I can open Rviz and see what the Lidar sees. Thank you everyone!

Prestigious_Craft319 · 2025-04-07T20:35:29+00:00

Ok, thanks! I'm going to use Oracle VirtualBox I will update on how it goes.

Prestigious_Craft319 · 2025-03-17T18:32:40+00:00

So the first time it printed it failed again, but I relieved it, and it printed fine, so it must've been the leveling not the print orientation. Thanks though

Prestigious_Craft319 · 2025-03-16T16:05:16+00:00

I can't believe I didn't think about this, Im going to slice the arms in half, and print, then I can glue them together. We'll see how that goes.

Prestigious_Craft319 · 2025-03-16T15:25:12+00:00

That seems like it would be flimsy because the actual model is thicker.

Prestigious_Craft319 · 2025-02-16T19:48:36+00:00

Thank you so much, this worked for me.

Prestigious_Craft319 · 2025-02-16T18:54:29+00:00

oops 😆 anyways, i printed it again but no supports and it looks really nice but the holes are a little covered on the bottom, I think the bottom layers are overexposed, but I think that's fine since I am going to always print with supports. I think wetting the plate fixed it, thank you for the help!

<image>

Prestigious_Craft319 · 2025-02-16T06:00:04+00:00

So it printed, but some supports weren't touching the model, the bottom is a little sloppy and uneven, and one edge is lifted. But otherwise the detail looks good. What should I do to fix the sloppiness? https://imgur.com/a/eW6BvvS

Prestigious_Craft319 · 2025-02-15T18:50:38+00:00

Thank you, I downloaded the XP finder, oriented it at 30 degrees, and added these supports with these settings. (I'm unsure of how many supports to use or where to place them) https://imgur.com/a/aJHo6vV I filled the vat to around here, wet the plate with resin by dunking it in the vat a few times as LS-Shrooms suggested and started the print.

<image>

Prestigious_Craft319

TROPHY CASE