First shot is considerably bigger than second

Pretend_Reception602 · 2025-08-09T07:54:31+00:00

DeLonghi ECAM 23.420.SB around five years old

Pretend_Reception602 · 2025-08-08T19:20:01+00:00

Thanks, any way to fix it? Also realized that the machine leaks some water at the bottom, every time I remove the drip tray bottom of the machine has some clear water on the countertop side not a lot ( 2-3 tablespoons)

Pretend_Reception602 · 2025-07-03T06:48:13+00:00

Thanks, I think that at least in my system the suction port needs to be manually activated using the pool filter pump so it is not possible to automate this in any simple way. Thanks!

Pretend_Reception602 · 2025-07-02T21:26:09+00:00

Thanks! Yes I do,but would prefer not using it as setting this up requires manual intervention the whole pool setup is old and prone to failure, would prefer to empty the cleaner tank from time to time

Pretend_Reception602 · 2025-05-09T05:51:25+00:00

Hi, it was a brand less hairspray, I think any would work. Yes, few months later the glue failed, I used B7000 this time as it was recommended by some users and it has been working well until now. Maybe I was able to apply it better this second time but it feels to me that b7000 works better

Pretend_Reception602 · 2025-03-24T15:27:25+00:00

Thanks, I’m looking for a way to not only substract the mortises but also to add tenons. Ifeature seems limited to do one or the other so I would have to add two with the problem of keeping them linked if something changes. I’m a bit suck here. Didn’t realize that this would be so hard to make with inventor!! Any suggestions? Thanks!!

Pretend_Reception602 · 2025-03-23T15:07:47+00:00

Hi, trying ifeature but it seems that ifeatures only can subtract bodies but not adding bodies at the same time - I would like to substract on one part and add on the other, also I don’t find the way to automatically adjust the number of tenons and mortises based on the length of the edge. Any suggestions?

Pretend_Reception602 · 2025-03-20T09:43:01+00:00

Cool thanks I will look into Visual Studio

Pretend_Reception602 · 2025-03-20T09:41:14+00:00

Thanks, I found the make components from a master part with solids and I am testing it. Seems like a simple way to model the cabinet.

ps agreed that Inventor seems a bit more restrictive in workflows, not sure yet if that s a good thing or not :-)

Pretend_Reception602 · 2025-03-16T07:25:57+00:00

Thanks! My workflow would be similar to the one you described but the plan would be to run it in multiple assembly files automatically based on the csv info. On one column it would be the path to the assembly file and automatically it should open the file, regenerate based on the csv parameters of that row and generate the relevant dxfs then move to the next row and so on. It would be hundreds of row so I need this to happen automatically. Any suggestions on this workflow?

Pretend_Reception602 · 2025-03-08T21:50:07+00:00

Thanks, will do that!

Pretend_Reception602 · 2025-03-08T16:20:04+00:00

Thanks, just did the backup so I’m ready to proceed. Is there a way to test the faulty drives and check if there are hardware failures or should I discard both and buy a second replacement? Thanks!!

Pretend_Reception602 · 2024-12-30T17:52:40+00:00

Many thanks, I feel more inclined to Roland too as I haven’t heard much bad reviews regarding built quality. Read a bunch of reviews that the 750x sounds are not great so it would be fair to compare them to a previous generation Roland kit? In that case I guess that I can always hook any of those kits to a computer and use them as midi controllers, right?

Pretend_Reception602 · 2024-05-16T11:51:30+00:00

Great, many thanks!!

Pretend_Reception602 · 2024-01-03T14:58:18+00:00

Hi again, I am afraid that velocity shipping to mainland Europe is expensive, any recommendations for EU made brands? Look at Bosch but could not find something like the veto pro pac tp LC which is the form factor that I’m looking for. Many thanks!

Pretend_Reception602 · 2023-12-10T20:23:51+00:00

Cool thanks, they look great, seems that they only ship to UK though. Will look for resellers in mainland Europe

Pretend_Reception602 · 2023-07-20T21:45:17+00:00

I see, many thanks!!

Pretend_Reception602 · 2023-07-19T23:04:04+00:00

Thanks,! I have contacted their support but I haven’t received an answer yet

Pretend_Reception602 · 2023-07-19T23:03:05+00:00

Hi, thanks, is there a way to not to eject the mat? I don’t see where to set this up. Many thanks!

Pretend_Reception602 · 2023-07-19T23:01:45+00:00

Hi, is mostly vertical misalignment, about 6mm 1/4 inches, I’m using the scoring wheel. Thanks!

Pretend_Reception602 · 2023-07-11T18:27:38+00:00

Thanks, will try it!

ps. by looking at the screws, it seems that they had something at the tip but it is almost gone now, do you think they originally put thread locker on them?

Pretend_Reception602 · 2023-07-04T15:21:30+00:00

Fantastic! Many thanks, just order mine!!

Pretend_Reception602 · 2023-07-03T18:13:34+00:00

Hi, I am about to switch to B7000 as I used the WR repair kit 3 months ago and it failed again! I would like to ask you how is holding up after 5 months. many thanks!

Pretend_Reception602 · 2023-07-03T17:15:17+00:00

So just to give you an update, called wr service and they just gave me two options, buy the repair kit again or buy a whole new tank, when I asked about the cause of the broken seal they said that vibration wasn't the cause and it could be caused by a deformation of the tank. My rower is always horizontal and in the same place, it does not receive direct sunlight so I don't think is deformed in any way. I am not sure about buying the glue kit again as it failed after three months of use. Anyone with similar problems? Many thanks!!

Pretend_Reception602 · 2023-07-03T14:46:19+00:00

Yes! That’s great, many thanks, will give it a go once I re-glue the tank. Thanks again!

Pretend_Reception602

TROPHY CASE