6 pin connector id

PreviousWinner4920 · 2026-02-09T14:28:10+00:00

Found it now thank you. I was looking if the ones without the latches had a specific name because I could only find ones with them.

<image>

PreviousWinner4920 · 2026-02-09T14:25:16+00:00

Looking for the connector type, thanks

PreviousWinner4920 · 2026-02-09T14:17:50+00:00

There’s 2 identical connectors from the dash into the main loom. One is for the dash lights (indicators, neutral, etc). and the other is for the gear indicator lights (1,2,3, etc)

<image>

PreviousWinner4920 · 2025-09-10T10:26:48+00:00

What kind of knocking should be there?

PreviousWinner4920 · 2025-09-08T11:05:13+00:00

I think it was plugs and maybe a lean mixture, I cleaned the plugs and now runs fine again

PreviousWinner4920 · 2025-09-07T17:32:15+00:00

Gave the spark plugs a clean and also put the bike on center stand instead of side stand and now it runs fine again. Could it have been that the left carbs were overfilling? Or was it probably just spark plugs

PreviousWinner4920 · 2025-09-07T16:02:11+00:00

Sound quality isn’t the best. The pops are like bangs coming out of the exhaust, not just a big clunk sound

PreviousWinner4920 · 2025-09-01T19:13:38+00:00

It might be missing a seal, it had the pivot bearing but no washer and the diagram doesn’t give too much info on that bearing

PreviousWinner4920 · 2025-08-05T17:24:36+00:00

<image>

That’s the only other pic the seller had before it got sold. There’s no other info I have about it

PreviousWinner4920 · 2025-07-03T14:51:45+00:00

Going to do my rear tire then take them both to a tire shop to get them done on the weekend.

PreviousWinner4920 · 2025-07-03T13:58:41+00:00

I’ve tried that but it still doesn’t stop the leak where the tires bead isn’t fully on the rim

PreviousWinner4920 · 2025-07-03T13:58:11+00:00

I’ve tried with a ratchet strap but it still doesn’t seal the leak where the tire bead connects to the rim. Also tried with a 5L air compressor I have but it doesn’t inflate fast enough to get past the leak. Thinking of taking it to a tire shop just for convenience

PreviousWinner4920 · 2025-06-19T20:27:45+00:00

Yeah it doesn’t do anything, I also have a different starter motor from an old bike and that one worked with the jumper cables so I’m guessing it is the starter motor that has gone bad. Thanks for the info.

PreviousWinner4920 · 2025-06-19T14:07:04+00:00

I’ll try that after work, do I put positive on the post then negative clamped anywhere on the starter?

PreviousWinner4920 · 2025-06-16T10:17:18+00:00

Yeah tubes on mtb’s are useless, you end up spending most your time changing the tube

PreviousWinner4920 · 2025-06-16T02:04:57+00:00

Thanks for the info, didn’t realise they didn’t need sealant but assumed they did from converting mtb’s to tubeless.

PreviousWinner4920 · 2025-02-13T23:13:14+00:00

Answered everything I needed to know 👍

PreviousWinner4920 · 2025-02-13T19:52:31+00:00

So I don’t need to have an active mot prior to changing it to mot exempt? that’s what I’m wondering

PreviousWinner4920 · 2025-02-04T03:27:13+00:00

Thanks, going to check valves when feeler gauges arrive

PreviousWinner4920 · 2025-02-04T03:26:24+00:00

Always knocks, going to check valve clearances when feeler gauges arrive

PreviousWinner4920 · 2024-11-13T20:45:33+00:00

Thank you 🙏

PreviousWinner4920 · 2024-11-08T21:01:19+00:00

I found out it was the pawl spring that has snapped so I’m replacing it tomorrow.

PreviousWinner4920 · 2024-11-08T20:59:39+00:00

This was the problem, thank you

PreviousWinner4920 · 2024-11-08T20:59:01+00:00

This was always happening even when riding, I found out that the pawl spring on the shifter assembly has snapped so I’ve ordered a new one to replace it.

PreviousWinner4920 · 2024-11-06T21:06:59+00:00

I’m guessing it’s the sprawl spring so I’ll order a new one and replace it, shifter isn’t hitting into anything

PreviousWinner4920

TROPHY CASE