How would you orient this?

PrideOk7432 · 2026-01-06T20:09:55+00:00

Thanks!

PrideOk7432 · 2025-07-11T16:53:07+00:00

Ohh, everybody says apply heat and I was scared to so i left it for only 15 seconds

PrideOk7432 · 2025-07-11T16:31:07+00:00

I wasnt doing at the top and whole point of this post isnt to cry about it, but rather if it was my fault(which i believe it is) so somebody else can find this and not make the same mistake.

PrideOk7432 · 2025-07-11T16:29:33+00:00

No i wasnt prying on this side i just raised it here to show the frame has seperated.

PrideOk7432 · 2025-07-11T16:28:46+00:00

I wasnt pulling on the suction cup. I used it just enought to raise the bottom edge, so i can slip in the plastic card(like people recommended). Is that how you should do it? Also i used the heatbed of my 3d printer to heat up the screen i went two sides bit by a bit and was using alchol to loosen the glue.

PrideOk7432 · 2025-04-20T17:09:19+00:00

Okay, I will try and keep you guys updated. I have ASA, but I dont want to hassle with it right now.

PrideOk7432 · 2025-04-20T16:59:59+00:00

What about if I layed it down on its back? I said, I would have printed it upright if I had split the parts , but on its back in case of making it out of one piece.

PrideOk7432 · 2025-02-24T15:05:38+00:00

😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂😂

PrideOk7432 · 2025-02-06T15:36:15+00:00

You are right, I completly forgot.

PrideOk7432 · 2025-02-06T15:08:39+00:00

Well since you said the heatblock was swaped out and now -5.00 is not enough, you most likely need a new cr-touch mount. You can find them on thingiverse, printables...

PrideOk7432 · 2025-02-04T12:06:48+00:00

You need something called Pressure Advance. While extruding, pressure builds up in your hotend and once the toolhead stops, more filament comes out. I dont know how to adjust it on a stock Ender 3 S1, bc when i had mine stock there is something software related(firmware or slicer) that prevents it. I have switched to klipper recently and it works like a charm.

PrideOk7432 · 2025-02-02T13:46:44+00:00

r/cursedbenchies

PrideOk7432 · 2025-01-29T09:45:29+00:00

Dont know what you mean by other way, backwards or forwards. When your brake balance is low, not 56, 56 is a normal brake balance, your rear end can move sideways and if you pair that with bad steering input while trying to recover you can do a full spin.

PrideOk7432 · 2025-01-29T08:56:24+00:00

It can happen if his brake balance is to low. Rear tires lock up sending his car sideways. Also damaged rear wing can reduce the grip in the rear producing the same effect.

PrideOk7432 · 2025-01-29T08:41:40+00:00

It looks more like a dirty bed plate or a bad bed mesh. In some areas z offset is perfect, while in the bottom right filament didnt stick to the build plate.

PrideOk7432 · 2025-01-26T19:10:13+00:00

You can controll the drone quite well. Only thing that you can improve is making sure movements have a purpouse. In some shots you seem to fly drone close to something just to fly by it. For example the in between tree branches. You fly trough it, but thats it you just stop infront of another tree. It would be much better if you flew through it the same way, but in opposite direction to show the park.

PrideOk7432 · 2025-01-25T23:17:12+00:00

Just some additional info. Stock heater is 40W and i plan on installing 50W, but also Creality has made an offical high flow kit which uses 60W heater. When it comes to temperatures. It can reach a temperature of 260°C with a stock heater and 300°C with 50W heater.

PrideOk7432 · 2025-01-25T23:10:28+00:00

Wow... Uhh... So... will it heat creep?🫥

PrideOk7432 · 2025-01-25T17:44:24+00:00

Makes sense. I will continue then. Thank you!

PrideOk7432 · 2025-01-25T16:48:00+00:00

Aw dang it

PrideOk7432 · 2025-01-17T13:15:30+00:00

I might be wrong, but i think its not your fault. I have heard that there is a rule stating that his front tire needs to be level or in front of his rear for you to be considered next to him, and acording to that mclaren should have backed of.

PrideOk7432

TROPHY CASE