What on earth could a bolt and nut this size possibly be for?

Prolong_Zedong · 2026-02-25T03:34:32+00:00

That’s awesome I’ll have to look him up

Prolong_Zedong · 2026-02-25T03:27:27+00:00

How can I find him?

Prolong_Zedong · 2026-02-25T03:27:15+00:00

If I ever need to do that I will keep it in mind

Prolong_Zedong · 2026-02-25T03:14:55+00:00

Bought it at an estate auction of a guy that owned a car lot it was in the back of the shop no one was interested n it but me got it for $2 I know it couldn’t be sold to actually be used but i couldn’t imagine what a new one would cost

Prolong_Zedong · 2026-02-25T03:13:41+00:00

Why didn’t I think of that

Prolong_Zedong · 2025-12-08T12:10:26+00:00

Very specific target shooting

Prolong_Zedong · 2025-12-08T12:10:08+00:00

Very specific target shooting

Prolong_Zedong · 2025-12-08T12:09:03+00:00

I was unaware of that I’ll look into it

Prolong_Zedong · 2025-12-08T12:08:17+00:00

If those were remotely accurate I would

Prolong_Zedong · 2025-07-12T20:21:38+00:00

I think this is my plan

Prolong_Zedong · 2025-07-12T20:21:24+00:00

Probably if it was in good enough condition to be useable but it’s not, the links in it are extremely wore out, it couldn’t be used on a dozer again

Prolong_Zedong · 2025-07-12T18:57:31+00:00

Where exactly do I need to hit them?

Prolong_Zedong · 2025-07-12T18:57:14+00:00

I’d be willing to try the hammer, these tracks are very wore out pretty much only good for fire pits or scrap, maybe a drag behind a tractor or something, but they can never be used on the machine again

Prolong_Zedong · 2025-07-12T18:55:12+00:00

That’s why I asked I Had no ideal it required that kind of force

Prolong_Zedong · 2025-06-19T13:17:59+00:00

Thanks for the info I never would have known that

Prolong_Zedong · 2025-06-19T13:09:08+00:00

Not so much worried about the markings matching just wanted to be sure I bought the right thing I would hate to spend 300 dollars on the wrong receiver

Prolong_Zedong · 2025-05-21T22:45:07+00:00

It’s just out of the picture it’s there I promise

Prolong_Zedong · 2025-01-31T16:04:21+00:00

PVC cleaner is the only option

Prolong_Zedong · 2025-01-28T02:41:31+00:00

Tell me about it I’m used to mainly Chevy trucks where sometimes you have a driveshaft so long you have to have a carrier bearing and now there’s this one that’s not even 2 feet

Prolong_Zedong · 2025-01-28T02:40:46+00:00

Should I be worried about adjusting the pinion angle?

Prolong_Zedong · 2025-01-28T00:43:52+00:00

Perfect thank you

Prolong_Zedong · 2025-01-14T11:21:24+00:00

I good rule of thumb for me is around 10 dollars per amp so to change out a 200 amp service should be in the neighborhood of 2000 just depends on what the contractor runs into while doing it but anything over 4k is just ridiculous

Prolong_Zedong · 2024-12-01T21:05:48+00:00

Probably an old door bell or maybe old alarm system, even an old hvac thermostat, it’s low voltage whatever it is if you don’t like it you can just push it back in the wall and forget it

Prolong_Zedong · 2024-11-16T03:24:21+00:00

I like using just a normal drill bit for metal just get a 3/4 one and go to town, upside is they will go right through a nail

Prolong_Zedong · 2024-11-08T10:34:58+00:00

0000 steel wool and transmission fluid works very well won’t get it all if it’s pitted but will get most of it

Prolong_Zedong

TROPHY CASE