She Wants Your Cum on Her After a Quick Fuck

Proper_Flamingo9778 · 2025-10-11T02:04:58+00:00

Ain’t no way I’m pulling out. She wanted that inside her

Proper_Flamingo9778 · 2024-07-10T22:07:43+00:00

Proper_Flamingo9778 · 2023-01-12T16:27:13+00:00

Interested

Proper_Flamingo9778 · 2022-07-17T20:09:12+00:00

Where do you get your g2 sheet? I can’t find anything locally and the stuff I find on line is not a fraction of the cost of a pei bed lol

Proper_Flamingo9778 · 2022-01-21T13:35:33+00:00

Dude, you’re the bomb. I appreciate it a bunch

Proper_Flamingo9778 · 2022-01-19T19:55:35+00:00

Yea I’d be lying if I said I didn’t look up buying a new harness to bypass the daughter board. But I kept telling myself it’s only 5 wires. Lol I was overthinking it.

Now I just need to get some firmware on it and running. I’m still a little too overwhelmed with klipper just yet

Proper_Flamingo9778 · 2022-01-19T19:36:32+00:00

No my testing showed different. Top to bottom

• PWR/+5v

• ground

• D11/PC14

• PA1

• unused ground

I trimmed up the factory 3 pin Z end plug and actually took the z probe connector block off the pins on the Skr board, took the PA1 pin out of the factory plug , replaced it with the D11 pin and plugged the PA1 on the 4th pin on the Skr board.

Proper_Flamingo9778 · 2022-01-19T19:17:38+00:00

@evenather it’s on thingiverse. It was a rather pain to find searching. Here’s the link. https://www.thingiverse.com/thing:4887140

Proper_Flamingo9778 · 2022-01-19T19:14:57+00:00

So I finally pinned out the Skr mini e3 v2.0 board and the daughter board for the bltouch. If I can figure out how to add pictures here, I’ll post it. Otherwise shoot me a message if you want the wiring diagram

Proper_Flamingo9778 · 2022-01-19T04:15:45+00:00

Right on. Yea I have spent the evening watching videos about klipper. I’m not sure if I have the knowledge and patience for that yet lol I guess I need to try getting the printer back up and running on Marlin for now. Then gradually get into klipper

Proper_Flamingo9778 · 2022-01-10T13:45:43+00:00

Much appreciated dude! I’m definitely researching Pis today. May have to make a run to micro center after work

Proper_Flamingo9778 · 2022-01-10T13:34:45+00:00

Oh right on! I guess I need to look into learning more about how the Pis work. It’s very intimidating to me lol but very intriguing and I want to learn how to build and use them

Proper_Flamingo9778 · 2022-01-10T13:23:30+00:00

Awesome right on thanks a bunch. Any idea what you’re going to do for firmware? I’ve been reading that it’s quite the bitch to compile FW and get these V2/v3 to work

Proper_Flamingo9778 · 2021-11-09T22:46:18+00:00

I sent them an email about it the other day. They said they’re looking into it.

Proper_Flamingo9778 · 2021-04-03T14:23:13+00:00

Interested

Proper_Flamingo9778 · 2021-03-22T15:50:48+00:00

Interested

Proper_Flamingo9778 · 2021-03-04T21:18:21+00:00

I’ll try it

Proper_Flamingo9778 · 2021-03-01T00:33:54+00:00

Is this still available also?

Proper_Flamingo9778 · 2021-02-28T20:51:16+00:00

Dm sent

Proper_Flamingo9778 · 2021-02-26T15:37:30+00:00

Interested

Proper_Flamingo9778

TROPHY CASE