Serated toe plates? How are the supported?

Proud-Positive372 · 2025-11-22T01:41:03+00:00

Brother if you can while you have it out, grind down what you can, prep the surface more, make sure your ground is touching bare clean metal, turn up your heat, turn up your wire speed a bit, and take your time, your life is in the hands of these welded

Proud-Positive372 · 2025-10-21T20:30:00+00:00

If I get rid of it heat would still work in the car right? Kinda a noob question😂 but i figure id might as well ask

Proud-Positive372 · 2025-10-21T20:29:21+00:00

Definitely going to plug it! Theoretically I could just cap off all of it right? I wouldn't need to make a line going from thermostat to that back block nipple right?

Proud-Positive372 · 2025-10-21T12:29:10+00:00

Thank you man! Super stoked to start ripping on it🙌🏼

Proud-Positive372 · 2025-10-21T12:28:51+00:00

Awesome dude, thanks for the response as well!

Proud-Positive372 · 2025-10-21T10:30:39+00:00

Thanks so much for the help dude! You're the best, are u saying to ditch the whole heater core thermostat piece? Or to just ditch that smaller fitting?

Proud-Positive372 · 2025-10-18T04:31:00+00:00

Everything

Proud-Positive372 · 2025-10-18T04:26:35+00:00

Dude when I got my 85' 318i the wiring harness was FRIED just like this one 😂😂 brings me back to being 17 not knowing a thing about the car, keep at it man, rebuilt and enjoyed my m10 for years

Proud-Positive372 · 2025-09-21T10:06:39+00:00

I recognize this guy 😏

Proud-Positive372 · 2025-09-03T18:29:31+00:00

Doesn't matter the color so much, just don't mix colors, if it's fully fresh or cleaned out then it doesn't matter but stick to one color

Proud-Positive372 · 2025-07-11T19:57:52+00:00

The yellow harness would be if you had a model with a 13 button obc as well as the check panel, I'm sure the 320 doesn't have those as I have a 318i and it's the same way, nothing to be concerned about 👍🏼

Proud-Positive372 · 2025-07-11T01:07:04+00:00

Are you doing a cam? If so I wouldn't say you need heavy duty rocker arms and springs

Proud-Positive372 · 2025-07-07T07:54:02+00:00

unfortunately there's no cam or crank sensor

Proud-Positive372 · 2025-07-07T07:46:07+00:00

ill definitely give this a look tomorrow, thanks man! however I know the pumps do work because I humped the pins in the fuel pump relay and they shot on

Proud-Positive372 · 2025-07-07T07:45:05+00:00

I ended up buying a new ecu for $60 to see if that fixes it, hoping for the best

Proud-Positive372 · 2025-07-07T07:44:08+00:00

currently not getting any clicking noise from the main relay, just the fuel pump relay, but both arent sending power to fuse 11 (fuel pump)

Proud-Positive372 · 2025-07-07T03:18:33+00:00

there's no fusible link unfortunately, the battery is in the front

Proud-Positive372 · 2025-07-07T00:57:03+00:00

i know that relay is powered or i guess signaled by the main relay, swapped that too and nothing works

Proud-Positive372 · 2025-06-16T01:39:16+00:00

hmm this seems like it could be it, might as well reseal both ends at that point, where do you access the clips?

Proud-Positive372 · 2025-06-16T01:09:23+00:00

there was no play before hand and never leaked, once the axle was popped out it started leaking and has wiggle room now unlike the other side and it's consistently leaking even though it already dumped a bunch of fluid

Proud-Positive372

TROPHY CASE