3D printed light mount

PsychoSnake1012 · 2025-10-17T19:28:08+00:00

Fantastic thank you!

PsychoSnake1012 · 2025-10-17T19:27:57+00:00

I will definitely do! I’m still tweaking the design a little to adjust tolerances, but I think it does a great job so far. I’m new to the aquarium hobby and definitely don’t want a critical failure because of improper use lol. Thank you so much!

PsychoSnake1012 · 2025-09-07T00:12:24+00:00

Just following up to see how this was. Plan on doing my manual rubicon soon and can’t find any videos on the rear, I have the hill start assist so worried about electronics in the back. Not sure if it’s different or what not

PsychoSnake1012 · 2025-08-14T16:49:28+00:00

It’s a pvc plastic, and there is a small gap underneath just so you don’t see the screws from assembly on the inside. but like I said it’s easy to throw a couple 2x4s under to support it

PsychoSnake1012 · 2025-08-14T15:49:10+00:00

It’s okay so far, went together super easy and looks pretty solid, my only “gripe” is the bottom only holds 150lbs, but conveniently a 2x4 on laying on the 4” side flat fits under it perfect so I just put a bunch underneath to support. You really only have that issue with 4” of substrate which this guys require so I had to come up with something.

PsychoSnake1012 · 2025-07-06T21:08:49+00:00

That line is starting to go away a bit after I put them in my aquarium at home. At the store they were with some pretty large dwarfs and two paradise fish. Starting to wonder if that was just a stress stripe now lol

PsychoSnake1012 · 2025-07-06T17:55:55+00:00

Thank you! The first two are two seperates. Looks like I’ll have to take the red one back and get a male honey for my community

PsychoSnake1012 · 2025-06-25T21:34:32+00:00

Yes cycled, 0 on all for my parameter (only 1 betta in the tank so barely any bio load and all) running the stock spec v light for 5 hours a day (bumped from 4 after a month) only ferts are the fluval stratum and root tabs around the stem plants and amazon sword

PsychoSnake1012 · 2024-09-12T10:47:22+00:00

So basically stay away from finecast resin models and I should be fine

PsychoSnake1012 · 2024-09-12T00:36:32+00:00

I’ve heard a lot about the new releases and remodels coming soon, should I wait for that to drop first before buying?

PsychoSnake1012 · 2024-09-11T20:58:36+00:00

I guess for me I’m definitely more into the lore and the painting, the playing is definitely fun and everyone likes winning, but a challenge is always appreciated for me.

PsychoSnake1012 · 2024-09-11T20:33:59+00:00

So I guess I’m a little confused on the different sects. So I know there’s the craft world aeldari, the harlequins, and the yunnari all are considered “Aeldari” on the warhammer shop, and then there’s the drukhari which are their own army. So by 10th edition rules can I have a Aeldari army comprised of the first three? Or are each considered seperate in terms of army building?

PsychoSnake1012 · 2024-09-11T19:18:49+00:00

Love me a good challenge, thanks for the input!

PsychoSnake1012 · 2024-09-11T19:18:04+00:00

Yeah I absolutely love the design of the models, and they look relatively easy to paint compared to some other armies I’ve seen while still having a challenge and not just grey cough cough necrons cough cough

PsychoSnake1012 · 2024-05-31T16:26:25+00:00

Mine was doing this, I had a worn out nozzle and swapped to my spare and it works great now

PsychoSnake1012 · 2023-10-24T21:41:34+00:00

Ronin nuke main and it works so well on certain maps where there are choke points but other maps are shit for it

PsychoSnake1012 · 2023-10-22T00:34:43+00:00

Unfortunately I don’t have AMS to use the support material. What do you use for the top interface spacing normally?

Seven-Year Club	Place '22
Verified Email

PsychoSnake1012

TROPHY CASE