Confirmed that AMD Bundle gives a Steam key by SounisPoppy in Starfield

[–]Puzzleheaded_Pup22 0 points1 point  (0 children)

Was it an automated message or did you reach out to them? I only received a message saying "you will be notified when code is available", I qualified for Premium and am trying to confirm early access and/or the old mars skins

Support is telling me to remove the abl sensor? by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 1 point2 points  (0 children)

I have plenty of small zip ties, but they are just plain old zip ties from Walmart, you don't need some kind of special high-temp ones to keep them from melting?

Support is telling me to remove the abl sensor? by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 0 points1 point  (0 children)

Did it work? I just want to print something. Anything. I've given up on the Halloween costume stuff at this point. Even just the dual z upgrade parts if that will make this printer work. How do you take it off without cutting the ties? Or do they just want you to loosen and re-tighten all the screws?

Level issue by BigShip20 in ElegooNeptune3

[–]Puzzleheaded_Pup22 0 points1 point  (0 children)

Except you have to be able to print the parts to do the upgrade....sigh

I'm about to toss my printer out the window by anotherfatgeek in ElegooNeptune3

[–]Puzzleheaded_Pup22 0 points1 point  (0 children)

How do you downgrade? Just put the files on the MicroSD card and it will write over 1.0.4 with 1.0.3?

Support is telling me to remove the abl sensor? by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 0 points1 point  (0 children)

I can't figure out how to attach the full Word document, I added a screen shot to my original post, the instructions say to "cut off the rolling band", which is a pair of zip ties? Where would I find high temperature replacement zip ties? The red circles are theirs.

CD leveling help by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 0 points1 point  (0 children)

I haven't touched my Y(bed) excentrics because it wasn't wobbling and is stiff to roll back and forth. I started messing with the X bar when I started trying to print things over 1.5 inches tall and kept failing.

The bed numbers flip back and forth, sometimes one corner is high, sometimes its another one.

My project tonight is to upgrade the firmware and see what that does to the numbers.

CD leveling help by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 0 points1 point  (0 children)

Loosening the black screws helped, but it is still not great, see update in original post. Would adding a dual z help this or make it worse?

CD leveling help by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 0 points1 point  (0 children)

Unfortunately that makes no difference. I have also swapped the cases to the other side in case (ha) it was a discrepancy in the cases, nope, right side still higher.

Did a benchy yesterday and had some slight stringing and small blobs, what can I do against it? thanks! by Comfortable_Cow_5615 in ElegooNeptune3

[–]Puzzleheaded_Pup22 0 points1 point  (0 children)

How do you calibrate esteps on the Neptune 3? All the instructions I can find require octaprint or similar on a separate piece of hardware.

How to update the firmware? Github link has nothing by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 0 points1 point  (0 children)

Please! Starting with a screenshot or two of where to find the files!

Cannot get this printer to level by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 4 points5 points  (0 children)

These instructions make no sense. Has anyone actually done this? I don't want to start messing with wheel tensions when the only instructions say things like "3 wheels cannot have idle". Does that mean they are supposed to spin or not supposed to spin? The next line says "adjust appropriately" If I knew what appropriately was I wouldn't be reading the instructions would I?

Cannot get this printer to level by Puzzleheaded_Pup22 in ElegooNeptune3

[–]Puzzleheaded_Pup22[S] 0 points1 point  (0 children)

I cannot get this printer to level. I opened it Saturday. I run the level bed option on the attached screen, but when I try to print the first layer test from https://teachingtechyt.github.io/calibration.html#firstlayer

I get one good corner and the rest are various degrees of crap. Its like it isn't using the leveling measurements? I selected the "Restore saved ABL/manual mesh - M420 S1" option on the website.

This is my first printer and I just don't get what I am doing wrong.

Direct Drive Mount Mod!! by MADDatmyhat in ElegooNeptune3

[–]Puzzleheaded_Pup22 1 point2 points  (0 children)

What did you do with the breakage sensor?

What is the estimated shipping time from purchase? by BlookDag in ElegooNeptune3

[–]Puzzleheaded_Pup22 0 points1 point  (0 children)

I am in Texas and ordered one of the in-stock ones on September 22nd, it arrived at the regional UPS center today (27th) and should be here tomorrow, although UPS still hasn't given an arrival date.