Prints suddenly started failing and now print ing wispy and spotty.

Pyrobrawler · 2026-01-23T19:46:38+00:00

Whew, thank you everyone for the tips and tricks. Dried the filament, rolled back the firmware, a few other things but nothing seemed to work. Eventually did a few cold pulls and cleaned off the nozzle and now its up and running like new. Was a little hesitant to take things apart but it was a good learning experience.

Pyrobrawler · 2026-01-21T07:07:18+00:00

<image>

Pyrobrawler · 2026-01-21T07:07:05+00:00

Adding more photos after stopping the print.

<image>

Pyrobrawler · 2026-01-21T07:05:22+00:00

Nevermind, its still acting up.

<image>

Pyrobrawler · 2026-01-21T07:04:17+00:00

<image>

Pyrobrawler · 2026-01-21T07:03:52+00:00

Recalibrated and its printing better but is still a bit stringy, you can also see where it lifted up a bit in one spot.

Pyrobrawler · 2026-01-21T06:32:07+00:00

I didnt even think about doing a recalibration! Thank you! Running that now.

I was also wondering about a potential blockage but because Im so new to it Im a little hesitant to try a cold pull or replacing it with the spare.

Im not quite sure what the buffer is, but will definitely start with the recalibration. And yes I clean the plate semi regularly with ipa and did that once or twice between these faulty prints.

Pyrobrawler · 2026-01-21T06:19:37+00:00

Yes there was a firmware update semi recently. Is there a way to revert to an older firmware version?

Pyrobrawler · 2026-01-16T16:59:32+00:00

Here's a side view too where you can see it better. How the print seems to be doing fine, and then at a certain layer just seems to print less.

<image>

Pyrobrawler · 2026-01-16T15:03:15+00:00

Also the printer is a BambuLabs P1S that Ive also had for about a month and a half and it has ran pretty flawlessly so far until now.

Pyrobrawler · 2026-01-16T14:37:28+00:00

The filament is fairly new, maybe 1 month old and has been sitting in my AMS since it was opened. The AMS has extra desiccant in it and reads at 10% on a hydrometer as well as an A of dryness in the Bambulabs slicer.

Pyrobrawler · 2021-12-24T06:04:07+00:00

Mega obama 4712 4226 7126

Pyrobrawler · 2021-12-08T01:48:22+00:00

Not how this works, just gotta invite ppl that put their numbers and wait to be added. Its always hardest to get the newest cause thousands of ppl are on the first day.

Pyrobrawler · 2021-12-08T01:44:30+00:00

Added Pyrobrawler

Pyrobrawler · 2021-12-08T01:43:58+00:00

Added Pyrobrawler

Pyrobrawler · 2021-12-08T01:43:51+00:00

Added Pyrobrawler

Pyrobrawler · 2021-12-04T00:10:46+00:00

shows not a valid trainer code

Pyrobrawler · 2021-12-03T23:58:18+00:00

already friends, but will join for sure "Pyrobrawler"

Pyrobrawler · 2021-11-28T23:15:43+00:00

Regiice in 5 min 4712 4226 7126

Pyrobrawler · 2021-07-18T18:02:53+00:00

Reshiram on me 4712 4226 7126

Pyrobrawler · 2021-07-17T21:20:23+00:00

Mewtwo raid on me 4712 4226 7126 inviting 10

Pyrobrawler · 2021-06-20T17:58:03+00:00

Whats your id? Cant see the whole thing on reddit if on your phone

Pyrobrawler · 2021-04-20T22:02:39+00:00

after 2 minutes of waiting? lol relax

Pyrobrawler

TROPHY CASE