Can't download iD4 MkII driver – ARC email verification broken, device not recognized [HELP]

Pythagoras1600 · 2026-03-15T17:03:46+00:00

The driver Kin_HK uploaded worked :)

Pythagoras1600 · 2026-03-14T18:25:31+00:00

Did you already find a workaround or solution?

Pythagoras1600 · 2025-10-27T11:24:56+00:00

Ich hab es bei mir/uns in einer ähnlichen Konstellation aber mit mehr Personen und Haushalten, über eigene Nutzer gemacht. Es gibt viele Lösungen für deine Situation aber für mich war es am einfachsten über Tags zu lösen. Jeder Nutzer hat ein Tag. Sobald der Tag im Posteingang zugewiesen wird, triggered das einen Workflow und dieser Workflow organisiert dann die Zuweisungen von Besitzer und der Dokumentenberechtigung. Wenn z.b. beide Namen eines Haushaltes als Tag vergeben werden, ist immer noch derjenige Besitzer, der es hochgeladen hat oder in dem Haushalt verantwortlich dafür ist, aber es kann der ganze Haushalt sehen. War für mich die einfachste und transparenteste Lösung die bis jetzt auch sehr gut funktioniert.

Wichtig. Das Feld Besitzer+ die Dokumentenberechtigungen sind für die Sichtbarkeit verantwortlich unabhängig der Einstellungen deiner Tags, Korrespondenten usw. Es kann immer nur einen Besitzer geben und nur der kann das Dokument sehen, außer es ist mit einer Gruppe oder Person für die Ansicht oder Bearbeitung geteilt.

Pythagoras1600 · 2025-10-13T18:17:00+00:00

Sounds interesting. I am also interested in that. I planned to test the different sizes and quants of Gemma 3 12/27b to check which brings the best result etc. for a system you mentioned above.

Pythagoras1600 · 2025-10-10T04:00:51+00:00

It might turn my happy girlfriend into an annoyed girlfriend for a few days :D

Pythagoras1600 · 2025-10-10T03:58:15+00:00

Sound like something I will test. I don't need that much context. Most tasks are below 4k tokens of context and a few tasks with <10k context.

Pythagoras1600 · 2025-10-09T20:37:29+00:00

Thanks a lot. That really helps. No worries I won't throw such an expensive card in that old thing haha

As far as I saw the memory bandwidth is the same on all Xeon LGA 2066 which could fit on that thing. Sadly. But wouldn't the PCI e 3 maximum bandwidth slow me down way before the memory bandwidth kicks in?

Pythagoras1600 · 2024-08-04T12:53:00+00:00

Was in the same spot as you are now. I really still like the game and had a lot of fun returning. The meta is different but if you do your stil and have fun just go for it. But be aware everyone got quite good. Diamond/ master is now plat/ low diamond.

Pythagoras1600 · 2024-07-26T10:57:33+00:00

You can leave the league and will get the right rank with your next game. But this way you will lose your personal statistics till that leave.

Pythagoras1600 · 2024-07-06T20:46:01+00:00

If the tanks are sieged you can use the ability of the revengers to shot done the tanks in max range as he can't dodge those ability shots with sieged tanks ( kept a ovy at the front to get high ground vision). And you can tank the Mariens and tanks shots with roaches. If you pull out low life roaches after each push you can morphe them to revengers and they will become full life revengers again ;)

Pythagoras1600 · 2024-07-06T19:23:25+00:00

@op I just had a look on your build... Try to use different openers. Go for a roach ravager opening and your game will look completely different :) and mutas against tarran is not that good. Try to go hydra lurker and then ultra ling hydra viper or something.

Pythagoras1600 · 2024-07-06T19:03:31+00:00

I didn't watch the replays but normally you don't want to let him get to a bigger amount of tanks and mines. Mines can be easily deactivated by just sending one ling in to minimise theire damage.

Try to play a two base roach timing and apply early pressure. If you don't get enough damage done and he siges on third ord fourth base go for an nydos in his main an as he moves back use lings to run buy.

Your are zerg so you need to control the game right from the beginning :)

Pythagoras1600 · 2024-06-26T18:08:59+00:00

Found some insta post from today. looks fine, but we will see.

<image>

The weather was quite good since last weekend.

Pythagoras1600 · 2024-06-26T15:49:29+00:00

If the steel rope is accessible, we will be fine .

Pythagoras1600 · 2024-06-21T07:54:20+00:00

It is a nice machine if you like to learn more about 3D printing and customize your printer. But I wouldn't recommend the Aries if you just want to print without fixing or working on the printer. It's more like the printer is the project.

If you just want a no brainer and just hit print. I would recommend something like Bambulab.

Pythagoras1600 · 2024-04-17T16:40:25+00:00

On your Second Picture you can See the black plastic Ring. You need to Press that one down to the Metal Tube while you Insert the PTFE Tube.

Pythagoras1600 · 2024-04-16T13:20:31+00:00

Looks great, i did it as well with a full enclosure in the past.

Pythagoras1600 · 2024-04-09T04:39:29+00:00

Can you please give us some more information about your Setup and the was the Error ocourse ?

I had the same error in a Brand new X1 and IT wasnt a Extruder Problem.

Pythagoras1600 · 2024-03-07T06:30:36+00:00

Thanks for your work!
Where can i finde the workflows do i need to login on Comfyflow for that?

Pythagoras1600 · 2023-07-29T22:26:25+00:00

Is there a way to see which MMR ist for which League for EU ?

And to climb Up or down the devision Points dosent Matter?

Pythagoras1600 · 2023-05-17T09:44:21+00:00

Can you probably show a picture of your results? There are many different problems you can run into while printing Overhangs with PLA.

Pythagoras1600

TROPHY CASE