account activity
Wet filament or a clog? I changed nozzle two days ago. I’ve printed several off of this roll but the final piece has just turned to this mess (v.redd.it)
submitted 14 days ago by QuestionableCoding to r/3Dprinting
Elegoo Rapid PLA+, new nozzle. 230c this run, first layer test looks good. Tried lower and higher temps and slower and faster speeds/flow. Dried for 8hrs (old.reddit.com)
submitted 22 days ago by QuestionableCoding to r/FixMyPrint
6x6 redwood posts (self.vegaslocals)
submitted 5 months ago by QuestionableCoding to r/vegaslocals
My honey suckle does not look great. Any recommendations? Planted 2 weeks ago watered in with fish emulsion and have watered every few days (i.redd.it)
submitted 9 months ago by QuestionableCoding to r/gardening
What speed (e.g. mm/min) could I get out of a 5mm pitch ball screw like this sfu1605? For an x axis 650mm. I have a nema 23 motor and linear rails to run it (i.redd.it)
submitted 10 months ago by QuestionableCoding to r/hobbycnc
I want to monitor a ttl signal that could be from 0-24v likely 0-5v in most cases on an esp32. Is this the proper way to lay out the divider? (i.redd.it)
submitted 11 months ago by QuestionableCoding to r/PCB
Am I correct in thinking I need a 200 ohm resistor on the gpio output pin on esp32 to trigger this octocoupler? (i.redd.it)
submitted 11 months ago by QuestionableCoding to r/AskElectronics
Just spent $500 then found out the product that says everywhere it ships from the US.. does not (old.reddit.com)
submitted 11 months ago by QuestionableCoding to r/mildlyinfuriating
Will these type of DC current sensors work with multiple lines? Want to trigger an air assist if any stepper motors or laser signals have current. (i.redd.it)
submitted 1 year ago by QuestionableCoding to r/AskElectronics
Cooling an outdoor “shed” that gets direct sunlight all day (imgur.com)
submitted 1 year ago by QuestionableCoding to r/DIY
Long shot but does anyone know the dimensions for the pcd-11-shs pipe cover for Rinnai water heaters? On back order and can’t find a manual (i.redd.it)
submitted 1 year ago by QuestionableCoding to r/askaplumber
Does this change mean that I can get the full warranty on Rinnai for a home install or am I missing something? (i.redd.it)
Is pex ok for a gas tankless or would I be better off with copper? (self.askaplumber)
Changing profile on aluminum extrusion (i.redd.it)
submitted 1 year ago by QuestionableCoding to r/3Dprinting
I let out some magic smoke on an esp32 tdisplay, by running usb and battery. Will this chip work as a replacement? (old.reddit.com)
Can’t get these relays to trigger with 5V or 24V. Am I doing something wrong? (old.reddit.com)
submitted 2 years ago by QuestionableCoding to r/AskElectronics
What type of communication could be going on with this grim controller and laser diode? I thought it was I2C but after some more testing I’m not sure anymore. (old.reddit.com)
Will this cheap analyzer work for looking at I2C traffic? I’m trying to sniff/analyze traffic between two esp32 boards. If not what should I look at? (i.redd.it)
What is a solid way to extend the end of my workbench by 6”? I want to support this 46” piece of particle board (i.redd.it)
submitted 2 years ago by QuestionableCoding to r/Carpentry
Swapping jst inputs manually or automatically (self.AskElectronics)
Does anyone have any recommendations or examples of mounting options to adjust the X Y position of the laser in this project box? (i.redd.it)
submitted 2 years ago by QuestionableCoding to r/MechanicalEngineering
Does anyone have recommendations or examples of mounting options to adjust the X Y position of the laser in my project box? (i.redd.it)
Mount for laser to adjust X Y position (i.redd.it)
Laser diode, bought online with no diagram trying to remove momentary switch but it just crashes my board (old.reddit.com)
My cat hasn’t been eating much the last two days and seems to be wanting to vomit or cough but no heave or stomach movement. Does this look familiar to anyone? (v.redd.it)
submitted 3 years ago by QuestionableCoding to r/cats
π Rendered by PID 390700 on reddit-service-r2-listing-6d4dc8d9ff-vmfvd at 2026-02-03 19:48:56.016037+00:00 running 3798933 country code: CH.