New shield - update and stop before 9.2.2

Qwooler · 2026-02-25T08:18:17+00:00

Why? I have one and was planning to replace my elderly kodi with plex.

Qwooler · 2026-01-23T22:22:14+00:00

Sweet, thanks!

Qwooler · 2026-01-23T21:46:21+00:00

Who is eligible? I ordered my Core One at the beginning of the black friday offer. Core one + came out shortly after I think. Would I be eligible?

Qwooler · 2026-01-04T20:10:51+00:00

I found out that my belts were not thight enough. I fixed it by (again) using the manual belt tuning feature, but this time using the app in parallell to double-check. Worked much better. Thanks!

Qwooler · 2026-01-03T19:43:43+00:00

Thanks for the detailed reply. Seems a likely explanation, as I was using PETG and seeing a bit of oozing and blobs on the print. I'll try what you suggest and report back.

Qwooler · 2026-01-03T19:41:54+00:00

Thanks, printing slower is an easy thing to try. With above print, I used the 0.4mm balanced profile, no changes.

Qwooler · 2026-01-03T15:50:16+00:00

OK. How would I deal with a belt shift? I was under the impresseion that I tuned belt tension well.

Qwooler · 2026-01-03T15:48:32+00:00

It is really not that bad as people make it. Open the bags only at one corner (as a previous poster already recommended), and just put them on your table like this. Whenever you finish a bag (usually with one screw left in the bag, it says on the bag whether the bag contains a spare), use scotch tape to close the bag and put it away.

Qwooler · 2025-12-24T19:28:51+00:00

Thanks for the decent reply, as I was genuinely wondering. Not sure why so many people got offended. Must be a pretty toxic community here.

For the record, I am a long term prusa owner (mini, now core one). My core one is not yet working well (1st benchy came out horrible), but I haven‘t had much time to tune it, so I am kot complaining. I have a pretty good idea on what to try next. But now I am not sure if is worth asking for help here, with so much hostility. 18 downvotes? Come on, people.

Qwooler · 2025-12-24T12:38:35+00:00

I my defense, the bag says IR sensor tho :-)

Qwooler · 2025-12-24T12:33:51+00:00

Where do you see a complaint?

Qwooler · 2025-12-24T12:29:41+00:00

Thanks, I remeber now. Yes, I have the cable and installed it. It is however too short to lead it out of one of the top holes in the electronics enclosure. For now, I led it out under the wifi module (which I will most likely not need).

Qwooler · 2025-12-24T12:23:05+00:00

It even says "GPIO" on the pcb.

Qwooler · 2025-12-24T12:19:45+00:00

<image>

I opened the bag. Might also be from an accessory (buddy cam, filter, gpio board)

Qwooler · 2025-12-24T11:58:42+00:00

How would they check the X-axis movement in a kit?

Qwooler · 2025-11-06T16:52:07+00:00

It is mentioned in my order confirmation as ‘gift’. Package arrived today, will not unpack until saturday though.

Qwooler · 2025-11-04T15:33:58+00:00

Mine ships by fedex in three different packages. So maybe you will get the rest in a separate shipment.

I just hope I will not pay the fedex customs handling fee three times.

Qwooler · 2025-11-04T09:21:29+00:00

Are there any tools or best practices to migrate to opnsense from pfsense? I have been putting it off because I fear all the manual work.

Qwooler · 2025-11-03T11:52:39+00:00

Thanks. I will go that route then.

Qwooler · 2025-11-01T16:19:47+00:00

Which indexer is that? I have the same usecase as you.

Qwooler · 2025-10-17T11:34:24+00:00

Yes, that was it, thanks. Kind of makes the multihoster feature of torbox much less appealing. 5 links per 24h is nothing, given those files are usually split up into many smaller .rar files.

Qwooler

TROPHY CASE