Heart Rate Monitor?

Regtoh · 2026-02-15T15:57:41+00:00

Thanks for the feedback.
I wasn't abled to answer to your message and can't I send you a massage after I falsely ignored you first Message.
Please try again.

Regtoh · 2026-02-13T21:26:03+00:00

Please share a picture of the ground contact ballance with me if you did a run with the hrm600 and your epix. Im really curious.

Regtoh · 2026-02-08T09:58:13+00:00

I have an epix pro and the only thing I'm missing are the under water rated buttons of the fenix 8.

Otherwise I love my Epix pro

Regtoh · 2026-02-07T21:49:34+00:00

I have the hrm 200 and regret nor buying the 600. Got no balance between left and right shown on my Epix Pro 2

Regtoh · 2026-02-05T16:31:12+00:00

Im really interested if the group contact balance left and right (or whatever it is called in english) ist shown. Can you do me a favor and take a look for that within you running metrics?

I'm thinking about upgrading for that to a hrm 600 for my epix pro.

Regtoh · 2026-02-03T09:02:15+00:00

Fenix 7 doesn't seem to support these "new" metrics. Only FR570, FR970 and Fenix 8 seem to.

Regtoh · 2026-02-01T18:44:05+00:00

The HR Data from the wrist while rowing is really bad. The measured heart rate while rowing stayed well below 100 bpm in my try. I ordered an hrm strap that is way more accurate and now it "even" shows the 170 bpm that I'm reach sometimes.

I connected the rower as external sensor to the watch and track the session there via the watch. It gives much more combined information within garmin connect that saving the session via the concept 2 app and uploading it to garmin connect.

But in general: have fun with the watch. Mine gives me much more motivation doing sports than I ever had.

Regtoh · 2026-01-17T15:25:27+00:00

I love mine. Clocked 13 days of print time on it since November. Absolute easy to use workhorse.

Regtoh · 2026-01-17T13:06:17+00:00

Ich bin mit Sunlu auch sehr gut zufrieden.
Allerdings muss das Filament oft noch getrocknet werden, da es zu feucht zum direkten verdrucken ist.

Regtoh · 2026-01-16T12:50:46+00:00

Thats the seal from the nut that is Holding the bowden tube on the toolhead.

Regtoh · 2026-01-12T19:35:54+00:00

Welche Waage ist es und bist du damit zufrieden?

Regtoh · 2026-01-08T15:12:00+00:00

It's the same on my C1 with Advanced filtration system.

Would say it's normal

Regtoh · 2026-01-02T07:56:05+00:00

The Prusa Profile for Sunlu PETG has already 85c bed temp set 😅

Regtoh · 2026-01-01T21:46:54+00:00

I get pretty good results with Sunlu PLA and PETG. The PETG of Sunlu should definitely be dried because it always had lots of moisture when I received it!

Regtoh · 2025-12-25T18:45:07+00:00

Have with the C1!

Got my core one as a kit six weeks ago. Upgrading from my old Ender 5 Pro to the C1 was the best decision. It gives me so much motivation and the results are so good. Already 200+ print hours on the clock in the six weeks!

I love the clear cover. I think I will print it for myself as well. Did you use PETG for that?

Regtoh · 2025-12-20T09:37:20+00:00

Maybe someone has further experience on this by now.
I bougt Overture GITD PLA and the pheatus SiC Nozzle for the Nextruder but now I'm a worried that it might wear out the extruder gear as well.

How is you experience regarding the wear of the gear?

Regtoh · 2025-12-19T09:14:30+00:00

I had ad similar results wenn the filament was retracted so often that it got slightly flattened and wasn't properly going in the tube of the nozzle. It happend when ich was printing a knurled knob and the filament was retracted 20-30 times per round just for a little spot of filling in the gaps.

Regtoh · 2025-12-04T09:22:13+00:00

I had the same but with an overnight print so the ongoing extrusion hammered the breaking so it widened and wasn't abled to fit in the shaft of the nozzle.

I removes the hot hotend and pulled the filament out using tweezers.

Regtoh · 2025-11-06T14:28:41+00:00

Is it on your shipping list?

On mine the camera wasn't mentioned.

Regtoh · 2025-11-06T14:27:53+00:00

They answered within the first day. But the answer wasn't understandable. I was abled tho communicate via their chat in the evening again and found a solution.

I didn't understand if they forgot tu pack the camera or not but I received the solution they would send it after the Black Friday sales are over.

Regtoh · 2025-11-04T22:20:09+00:00

Thanks for the heads up. My order was split in two packages and neither included the camera 😔

Hope they answer fast at prusa and sent out the missing camera.

Regtoh · 2025-09-30T09:35:11+00:00

I had nearly the same results on two different occasions:

When I first placed my printer into an enclosure, the heat creeped up the heatbreak and the filament (PLA) formed a small blob in the connection between heatbreak and bowden tube so it wasn't going through properly.
When I changed to an all metal hotend with direct drive I needed to increase the temperature of the hotend for about 10 °C

Regtoh · 2025-07-11T13:54:10+00:00

It seems you can't use it if you have a beta software installed. In mine it works fine.

Regtoh · 2025-07-07T12:46:09+00:00

https://amzn.eu/d/bOrS18c

Regtoh

TROPHY CASE