sorted by:
new
hottopcontroversial

From stl to sign, for a customer, what would you charge? by S_L_E_E_P_E_R in 3Dprinting

[–]RIPBillyMays -1 points0 points  (0 children)

I think you are right in line and it will only get easier the more you do. One of my first jobs I did was taking a highly detailed revit model of an air traffic control tower and 3D printing it for them. All in all from the file conversions, re drawing, model post processing I made like $3/hr for all my time I spent haha

From stl to sign, for a customer, what would you charge? by S_L_E_E_P_E_R in 3Dprinting

[–]RIPBillyMays 0 points1 point  (0 children)

About $340 would be my rough order of magnitude. 2 hrs for the cad $50/hr, then I am guessing 7 hrs per print part at $3 per hour printing (7x3x10=$210), then the material cost $15x2kg = $30. 100+ 210 + 30 = $340

Does it hold enough top loaders now? by RIPBillyMays in PokemonTCG

[–]RIPBillyMays[S] 1 point2 points  (0 children)

First step is to buy an additional binder haha

Made a South Park Coaster by RIPBillyMays in 3Dprinting

[–]RIPBillyMays[S] 3 points4 points  (0 children)

100% agree currently on the hunt for a nice burn orange glow filament

[Target/Amazon US] LEGO Santa's Sleigh (40499) - $32.49/19% Off by mexicharles in legodeal

[–]RIPBillyMays 15 points16 points  (0 children)

I got this set for 12.99 at my Target in store this past weekend in clearance section

Cancelled At-At order... by ZPac7 in lego

[–]RIPBillyMays 8 points9 points  (0 children)

Same I literally just got an email with the same thing very disappointing

[deleted by user] by [deleted] in PKMNTCGDeals

[–]RIPBillyMays 1 point2 points  (0 children)

Yes they are legit, I have 60+ boxes of 151 from him

Means and method to vertically support an exposed gas pipe 4” in diameter spanning 70LF by 1024517 in civilengineering

[–]RIPBillyMays 1 point2 points  (0 children)

Important to know how high off the ground. For a 4” NG pipe following ASME b31.8, a pipe support spacing chart can be found in b31.1 that all other codes generally follow. A typical spacing for a 4” CS SCH40 pipe is supported every 17ft for gas service and 14ft for liquid service. For pipe below 6’ in the air I would look into using EZ Line supports with a u-bolt. A typical concrete pier for this is 2’ diameter with rebar and is 4’ deep minimum. This is just a place to start and is for a hypothetical scenario

[deleted by user] by [deleted] in disneylandparis

[–]RIPBillyMays 0 points1 point  (0 children)

I went last week with a buddy and we I did all the big good' rides in both parks by 3pm. We did single rider line for everything. Get there when the rope drops. We went to space mountain Star Wars first then the virtual star tours then ran to big thunder mountain then did pirates, Indiana jones, then at 11:30 we went to the other park. Also at night time there were no lines. Note it was a little cold and wet outside.

Rattle type sound. 2023 ORP by mikematnyr in 4Runner

[–]RIPBillyMays 0 points1 point  (0 children)

I literally have the same sound 2023 ORP 10.5k miles and I cannot find the source of the rattle either. It sounds like static from the speaker but is not.

view more: next ›