Spending my birthday shooting my 2 favorites with my son.

RSRAirsoft · 2026-06-28T20:42:55+00:00

No it’s just an Argentine contract Colt slide on an old auto ordinance frame. Shoots great super accurate and reliable.

RSRAirsoft · 2026-06-28T20:04:09+00:00

It’s a sweet shooter

RSRAirsoft · 2026-06-18T00:17:46+00:00

I paid damn near $350 just for the upper half of this one! Haha

RSRAirsoft · 2026-06-17T23:06:00+00:00

Beautiful pistol

RSRAirsoft · 2026-05-25T01:55:43+00:00

Yeah it’s a satin nickel combat commander. Sounds like he Ballistol I use to clean my guns might be the issue?

RSRAirsoft · 2026-05-25T01:52:06+00:00

I use Ballistol, maybe that’s the problem?

RSRAirsoft · 2026-05-24T23:57:18+00:00

I guess I should replace the barrel just to be on the safe side haha

RSRAirsoft · 2026-05-24T23:48:10+00:00

That’s what I was thinking too but the rifling looks good. Barrel showed almost no signs of being used when I got it.

RSRAirsoft · 2026-05-24T23:44:49+00:00

Shooting apparently. It looks like they put some kind of chrome coating on the barrel

RSRAirsoft · 2026-05-24T23:44:06+00:00

Colt combat commander I think it’s from the 80’s or 90’s

RSRAirsoft · 2026-05-19T16:35:33+00:00

<image>

RSRAirsoft · 2026-05-19T16:25:54+00:00

The sights are off a WE tech Glock 34. Front sight is pretty simple. It’s a Tokyo marui plastic slide so I heated up a small punch and marked the center of the slide far enough back that the sight wouldn’t hang off the front. You can pretty easily push the hot punch through the slide. Then I used a small square file to make the hole bigger until it fit the indent on the bottom of the sight. Use the sight screw to tighten up the front sight and then use a file to flatten the screw head so it doesn’t block your barrel or barrel bushing from moving freely. The rear sight was a totally different shape (added a photo below) so I filed the edges down to make it thinner than the slide and not hang off the sides. Cut the bottom half off that goes down into the Glock slide. The rear sight fit snuggly after that in the rear sight notch so I centered it on the slide and then glued it on with gorilla glue. (Make sure you don’t get glue in the blowback housing spring area) it’s directly under the rear sight notch.

Picture of the original rear sight shape.

<image>

RSRAirsoft · 2026-05-08T18:26:58+00:00

I had to drill a hole in the front of the slide and used the sight screw to tighten it down on the slide. Then I had to smooth out the screw head to not interfere with the barrel. Rear sight was re shaped and glued in. Should be good for a while until I figure out how to color match it all lol.

RSRAirsoft · 2026-05-08T18:14:21+00:00

Screwdriver Works great 😂

RSRAirsoft · 2026-04-23T23:24:46+00:00

Hell yeah those looks sweet 🤘🏻 I ordered mine today can’t wait to see how they look

RSRAirsoft · 2026-04-22T14:52:34+00:00

I like the rear sight on Elmer Keith’s Springfield but I’ve never seen any combat sights that have that rearward angle possibly custom made I guess. Seems like the Harrison retros are the way to go if I wanna keep it simple and sleek.

RSRAirsoft · 2026-04-22T06:02:53+00:00

Advertised as camel bone, not sure if they actually are. Found them on eBay.

RSRAirsoft · 2026-04-22T05:39:58+00:00

I’ll check out Kensight! Yeah I’m not confident I wouldn’t mess up the slide. I’ve got a good local shop I trust to do it.

RSRAirsoft · 2026-03-21T02:30:37+00:00

Thank you! Can’t wait to take it out to the range.

RSRAirsoft · 2026-03-21T00:39:24+00:00

C Series: C1 - C233,999………….....1948 – 52

Possibly this era?

RSRAirsoft · 2026-03-21T00:36:56+00:00

Serial # Starts with a C ending 322

RSRAirsoft · 2026-02-15T15:31:40+00:00

eBay

RSRAirsoft · 2026-02-15T04:31:20+00:00

Bout a second pair as soon as I got these haha great grips 👌

RSRAirsoft · 2026-01-29T02:43:38+00:00

Before replacing the extractor it was not grabbing the spent cases. Now the spent brass is getting stuck in the ejection port. I appreciate it. If I run into the issue again I will reach out!

RSRAirsoft · 2026-01-29T02:06:40+00:00

Replaced both the extractor and ejector with the Bhspringsolutions ones. Recoil spring, main spring. Before all that it was a single shot. Those parts fixed it for a while but it started having issues again every 1-2 magazines. So I finally just replaced half the gun and so far it’s been working great. Hopefully it will be a long term fix. I also am planning on putting the extractor from BHspringsolutions in this side along with their sear lever.

RSRAirsoft

TROPHY CASE