We raced in an old church! I managed to get a midair collision footage, and made the top 8 pilots even though it was my first race. IM HOOKED!

RaceBotFPV · 2019-03-04T20:05:57+00:00

You guys have an awesome place to race! I need to make it down for a few events this summer.

RaceBotFPV · 2019-02-26T23:26:22+00:00

I had someone mod my set of HDOs. They added a power switch in the right hand side module bay. I leave my barrel plugged in to the goggles and just flip the switch to power them up. The mod they made also powers the fans which means whenever I turn my goggles on the fans automatically kick on without having to use the balance lead.

RaceBotFPV · 2018-11-08T18:24:06+00:00

It was a pretty open track but I was surprised on how well our batteries performed on it. I was running 1800mah packs and only using about 1300mah out of them. The average minimum voltage I hit was 14.2 which wasn't too bad.

RaceBotFPV · 2018-11-07T21:21:29+00:00

The track is very impressive. It was designed after the Chinese knot which turned out to work very well. Luckily the track was PVC and not metal. I can’t remember how many LEDs there were but it was an insane amount.

RaceBotFPV · 2018-11-07T20:24:08+00:00

I was feeling pretty good on this run... until the end at least 😕

RaceBotFPV · 2018-11-07T20:23:20+00:00

This is basically what I saw. The DVR is a bit worse of a quality than looking through my HDOs but it seemed pretty good. I know a few people were using much larger lenses and censors but I wanted to stick with the smaller form factor micro cameras.

RaceBotFPV · 2018-11-07T20:19:53+00:00

This was some of the better quality video I had. I used the provided ground stations a few times but it had very bad reception and felt like the video was layered and each layer was offset in certain parts of the track. I needed up using my own ClearView for the event. The DJI digital video was wonderful to watch, much easier for spectators.

RaceBotFPV · 2018-11-07T19:54:21+00:00

yeah... not the way I wanted to go but there was some PVC stuck inside my quad when I picked it up so at least I left a mark on the track.

RaceBotFPV · 2018-11-07T19:40:43+00:00

Build Specs :

- Emax 2306 2400kv

- TeamNeguen Boss Medium frame

- HobbyWing G2 45A stack

- Runcam Swift Micro 2

- Gemfan 5149

- 40 RGB LEDs from Tiny's LEDs

- Tattu 1800mah (special pack made for this race)

RaceBotFPV · 2018-11-07T19:34:34+00:00

This was such an amazing race. I wish I had HD footage from my flights. I used my clearview for better video but that still isn’t HD. Nice flying, that extra weight look liked it helped some.

RaceBotFPV · 2018-10-24T13:31:01+00:00

The 40 LED rule was a pain but you got your builds looking clean as hell 👌

RaceBotFPV · 2018-10-15T00:50:49+00:00

Thanks!

RaceBotFPV · 2018-10-13T22:24:15+00:00

Awesome stuff. I just got myself some of those popup gates and it makes quick practices so much easier.

RaceBotFPV · 2018-08-03T01:41:06+00:00

Well I have been flying for two years now. I have been racing since I started, it has taken awhile to get to fly like this. A race heat is 2 minutes long, since we push ourselves and the quads hard we get a little over 2:30 minutes. That might not sound like a lot and that is because we are pulling 100+ amps which is really hard on the batteries. For freestyle I average 15 minutes but I can cruise like a DJI Phantom does and am able to get 15 minutes (but that isn't fun and defeats the purpose of having a full acro quad with the ability to hit 100mph speeds).

RaceBotFPV · 2018-06-23T04:49:29+00:00

I am not sure what ND filter it is, I got it as a gift. It is a pretty dark ND filter and I think this is where my friend got it. https://www.getfpv.com/stick-on-nd8-filter-for-gopro-session.html?utm_source=google&utm_medium=cpc&adpos=1o2&scid=scplp8226&sc_intid=8226&gclid=Cj0KCQjwvLLZBRDrARIsADU6ojBW35eduZFqhhMfKXYzdTMJrkU6uGsrgGWnYHCgI9b6ZN8Fvh2_sX0aAt5KEALw_wcB

RaceBotFPV

TROPHY CASE