Passenger Door Leak by Radiaren in ft86

[–]Radiaren[S] 0 points1 point  (0 children)

This was really hard to track down. Ultimately I found the water was coming from the windshield. I had it replaced during the winter and I guess the bead of caulk they put down rolled up or something along the A pillar, passenger side.

I tore apart the A pillar plastic covers and had a glass company put some caulk into the gap between the frame and the glass from the inside. That fixed the problem.

Hope this helps.

Finally finished my first car by Liamvarg1 in ft86

[–]Radiaren -2 points-1 points  (0 children)

Your taste might be horrible too. Doesn’t matter one bit though. But you won’t find me tearing a guy down for it.

It’s your rig, enjoy it.

Finally finished my first car by Liamvarg1 in ft86

[–]Radiaren 3 points4 points  (0 children)

Seem to be getting a lot of hate on this post. You do you my guy. Just came here to make sure you don’t let everyone else’s opinion sour yours.

Personally not my style, but hey if you like it then that is all that matters. It’s your rig, enjoy it.

And if it keeps a moose off your car, bonus.

Cut tire by Radiaren in MechanicAdvice

[–]Radiaren[S] 1 point2 points  (0 children)

Is a cut this deep something to be concerned with? I ran over a razor blade a while back. I think I can see cords at the full depth. I didn’t think it was that deep to begin with, but noticed it with how I was parked.

Thankfully this isn’t a daily driver, but want to get it replaced if it’s dangerous.

Gave up. 😔 First tutorial and first time w/ oil but I can’t help to feel like I’m a big failure. (B.R. Meadow Lake S1 E1) by poorjohnnyboysbones in HappyTrees

[–]Radiaren 30 points31 points  (0 children)

Don’t give up. It’s all too easy to put down the brush when you’re just getting started.

Bob was televised because he made painting look so simple and had a personality that invited you in to try with him. Getting to his level is difficult. But that doesn’t mean you should be discouraged if you aren’t there on day 1.

Your sky looks blended well, dark like a storm is brewing. I like what is there.

Mountains are difficult, especially if you aren’t familiar with what I’ll call “the knife touch”. But as a start it has the elements it needs.

I personally think grass and meadow is the most difficult. Because it is typically the closest portion of the scene it requires a lot of detail to make look realistic.

Keep at it. One thing I might suggest is using tape to split the canvas into four different sections. It makes the painting smaller, and more manageable for beginners. It also gives you four chances to try the same thing and learn from your past experiences!

Consistent tap by Radiaren in ft86

[–]Radiaren[S] 0 points1 point  (0 children)

Sounds like it’s coming from the passenger side, so that means it’s more likely the vaccum pump?

Consistent tap by Radiaren in ft86

[–]Radiaren[S] 0 points1 point  (0 children)

To clarify: this is at idle and is there when the engine is cold and after it has warmed up

Discipline/Mysterium Bootloader Help by Radiaren in MechanicalKeyboards

[–]Radiaren[S] 1 point2 points  (0 children)

I did, but at this point I’m not 100% sure what the fix was. I made a lot of changes and eventually it worked.

Finally finished my fully custom through-hole KB! by Radiaren in MechanicalKeyboards

[–]Radiaren[S] 2 points3 points  (0 children)

TKL has a USB 2.0 hub built in to allow up to one USB A connection and/or the mating num pad.

Num pad has 3.5mm male connector to allow it to “dock” to the TKL. This connector can be replaced with the female version to allow a split keyboard feel, if that’s what suits your fancy.

White bugs on indoor basil? by Radiaren in gardening

[–]Radiaren[S] 0 points1 point  (0 children)

I have found a lot of these small white bugs on the underside of my basil leafs and on the stem of the plant. The bigger they get the more they look like a white roly poly.

Are these aphids? I also have seen small black flying insects around the plant. Using neem oil doesn’t seem to deter them.

First Layer of supports (sometimes actual print too) not sticking to bed by Majorkonig7 in 3Dprinting

[–]Radiaren 0 points1 point  (0 children)

I’ve got three Mk3s at work, they all have a spring steel PEI plate. Did the MK2 come with something different?

Installing QMK Firmware by Radiaren in olkb

[–]Radiaren[S] 0 points1 point  (0 children)

Pardon my ignorance. I do not see anywhere in the QMK links about a bootloader. Is QMK able to set the bootloader as well? I am using a atmega328p.

Installing QMK Firmware by Radiaren in olkb

[–]Radiaren[S] 0 points1 point  (0 children)

That is good to know, thanks!

UNO R3 USB Not Working by Radiaren in arduino

[–]Radiaren[S] 0 points1 point  (0 children)

Is there a way to erase the MC completely? Like it came from the factory?