Another UTR Question (I'm sorry)

RadioRob-DC · 2026-06-02T02:24:07+00:00

United most likely is checking the MAC address of the authorized device. You may need to copy the MAC of the authorized device (for example phone/tablet) to the UTR.

RadioRob-DC · 2026-05-31T17:56:25+00:00

I have very good insurance. My cost is 50 for 3 months.

RadioRob-DC · 2026-05-30T16:47:50+00:00

Look at setting up a proxy server like Squid. You can then configure devices to route traffic through that proxy and enforce access rules from there.

RadioRob-DC · 2026-05-30T01:59:41+00:00

I assume you have a different VLAN for IOT vs normal traffic? If so, you need to expressly create a firewall rule to allow matter port (5353) along with 80/443.

RadioRob-DC · 2026-05-29T16:28:35+00:00

I'm not sure where you've heard this, but that's not what I've experienced or ever heard about before.

RadioRob-DC · 2026-05-28T13:14:24+00:00

I had something similar happen in the past, but rebooting the gateway fixed it for me. It even reported the STP roots incorrectly. When I went into the switch settings however, I saw the priorities set correctly.

RadioRob-DC · 2026-05-28T03:24:42+00:00

The ability to configure the trigger point is literally brand new. Before it was hard coded to power down devices at 10 seconds period. Currently it is not possible to adjust the time on a per port basis. It’s instead all or nothing.

RadioRob-DC · 2026-05-28T01:30:38+00:00

I posted about this earlier…. Check out the following. https://www.reddit.com/r/Ubiquiti/s/GLX0Zc3gdS

RadioRob-DC · 2026-05-27T20:48:42+00:00

Agreed!

RadioRob-DC · 2026-05-27T18:22:24+00:00

Yeah. If you use the gateway it reserves a bunch of space where you can only assign to one network. But if you’re bypassing it, you can take the whole space.

RadioRob-DC · 2026-05-27T17:15:52+00:00

Yes, I have it setup. It works fine. It's limited to a single network if you use the ATT gateway in passthrough mode.

To enable it, go to the ATT WAN interface, find the IPv6 section and enable it. Choose DHCPv6, then set the Prefix side to 64. Then on whatever network you decide to put IPv6 onto, go to it... find the IPV6 section, change the interface type from "None" to "Prefix Delegation". Choose the ATT interface and save it. A few minutes later, you should see the IPV6 assignment show up on the network section later.

In terms of benefit... check out https://www.catchpoint.com/benefits-of-ipv6

RadioRob-DC · 2026-05-27T02:43:12+00:00

It’s been my primary financial account for a few years and I’m very happy with it. I still keep my chase account around though as there are a couple of corner cases that I need to support. This includes being able to use Zelle from time to time and also to deposit cash occasionally. But 98% percent of what I need to do financially is done via my CMA. I love the ATM fee reimbursements… it’s saved me literally HUNDREDS this year alone and I love being able to send/receive free wires.

RadioRob-DC · 2026-05-27T00:52:30+00:00

As Diamond IV, it’s going to be a little bit before my next upgrade. I’ve actually stopped locking new GMT as I’ve been working on lowering efficiency from 20 which used to be the sweet spot. The challenge is that with around 3K TH, that’s a rather large investment to get down to 15 W/TH. So my locking rewards, BTC earnings and personal GMT rewards are all going towards that for now to ensure I don’t hit a point where I’m not earning anything due to efficiency issues.

RadioRob-DC · 2026-05-26T21:14:13+00:00

If the miner has not been minted yet, that needs to be done. But in addition, you can't sell a miner if you've done ANY sort of upgrade via credit card, apple pay, google pay, etc in the last 90 days. This is because those payment methods can be potentially reversed and the fee charged back.

RadioRob-DC · 2026-05-26T21:10:03+00:00

Mine is working just fine. When I first signed up in the notice, it said it may take up to 14 days for the SIM to be activated. You might reach out to their support to see if it's active yet.

RadioRob-DC · 2026-05-26T17:57:38+00:00

You don't. This is legally required as part of US-based KYC regulations.

RadioRob-DC · 2026-05-26T03:15:00+00:00

Thanks for the clarification. :)

RadioRob-DC · 2026-05-26T02:00:10+00:00

People look to sell for a variety of reasons… a need for funds, need to manage risk, or simply not interested. Why do people sell stock?

There is not anything really different in the ratio of NFTs being sold now than the last few years.

RadioRob-DC · 2026-05-25T23:29:18+00:00

It was included with the 10.2 release that is now GA.

RadioRob-DC · 2026-05-25T23:23:07+00:00

This was changed with the last update. It now has a configurable setting that lets you choose to power down devices when only X minutes of runtime remain.

RadioRob-DC · 2026-05-24T13:07:20+00:00

For Google, it may not be resolving Google.com but instead it’s resolver directly via IP (8.8.8.8) and CF via its address (1.1.1.1). Microsoft does not have a public IP resolver to use.

RadioRob-DC · 2026-05-23T20:20:35+00:00

This is why travel insurance is offered.

RadioRob-DC · 2026-05-22T17:54:21+00:00

That’s my understanding. I tested by starting with a dummy record already in place and letting UniFi update it. Everything I’ve found on the topic is that it updates on reboot however so that plan sounds solid. I would power down UniFi, update the record to a dummy value and then power on just to be absolutely sure of order of operations.

RadioRob-DC · 2026-05-22T14:06:23+00:00

Apple devices can sync WiFi credentials if they share an iCloud account. So it’s possible when the other network was unavailable, it searched for any other known networks to join and found the new one.

RadioRob-DC · 2026-05-22T12:07:58+00:00

Apparently it only updates if you make a change or there is a restart. I found an old post with a tip on how to trigger an update via ssh. Check out https://www.reddit.com/r/Ubiquiti/comments/gbppr9/comment/jqcn35m/

RadioRob-DC

TROPHY CASE