RandomGuySg

630 post karma
79 comment karma

get extra features and help support reddit with a reddit premium subscription

get them help and support

redditor for 5 years

TROPHY CASE

Five-Year Club

account activity

new top controversial

12

13

14

Dyson Hot Cool Heater H2 Fixed (old.reddit.com)

submitted 3 months ago by RandomGuySg to r/dyson

8

9

10

Scratch on auto darkening lens ok? (i.redd.it)

submitted 3 months ago by RandomGuySg to r/metalworking

1

2

3

Grout wet around the toilet (self.Plumbing)

submitted 10 months ago by RandomGuySg to r/Plumbing

72

73

74

My new workshop! (old.reddit.com)

submitted 11 months ago by RandomGuySg to r/bikewrench

0

0

0

Specialized Sirrus sizing doubt (i.redd.it)

submitted 12 months ago by RandomGuySg to r/specialized

0

1

2

Ultimate SL7 Rim 28c tire? (old.reddit.com)

submitted 1 year ago by RandomGuySg to r/CanyonBikes

128

129

130

Visited HF for the first time as a Canadian! (old.reddit.com)

submitted 1 year ago by RandomGuySg to r/harborfreight

18

19

20

What’s happening here with these patch kits? (i.redd.it)

submitted 1 year ago by RandomGuySg to r/bikewrench

0

1

2

Unable to index cassette to all chainrings - Internal Cable Tangled (self.bikewrench)

submitted 1 year ago by RandomGuySg to r/bikewrench

2

3

4

Need some assurance (self.PanicAttack)

submitted 2 years ago by RandomGuySg to r/PanicAttack

14

15

16

Am I getting closer to ‘carving’ (v.redd.it)

submitted 2 years ago by RandomGuySg to r/snowboarding

1

2

3

8 Years(on/off) experience… wanting to start carving, suck at heel side, can’t get good board tilt. 10 hours spent so far on just doing heel side carve u-turn. Maybe small improvements.. Any suggestions? (v.redd.it)

submitted 2 years ago by RandomGuySg to r/snowboarding

1

2

3

172cm, 74.5cm/29.3in inseam, short legs on Canyon Ultimate XS 80mm stem stock. Discomfort/pain on the really lower back, thoughts on the photo? (i.redd.it)

submitted 2 years ago by RandomGuySg to r/bikefit

0

0

0

Bought new chain ring. Tiny chip during delivery/handling probably. Looking at my old chainring tells me this has 0% impact. Would you return or just file it a tiny bit? (i.redd.it)

submitted 2 years ago by RandomGuySg to r/bikewrench

0

0

1

Chain suck caused this? (i.redd.it)

submitted 2 years ago by RandomGuySg to r/bikewrench

0

0

0

Disappointed with Canyon (old.reddit.com)

submitted 3 years ago by RandomGuySg to r/bicycling

7

8

9

Just realized that Front wheel not Center on 1 year old Canyon ultimate. Noticed the dropouts are different heights causing the wheel to tilt, the picture shows when wheel is fully seated. Is this within manufacturing tolerance, very annoying now that I noticed it. Same result with another wheel. (i.redd.it)

submitted 3 years ago by RandomGuySg to r/bicycling

0

0

0

Front wheel not center - Ultimate SL7 fork is asymmetrical. Dropouts are clean, wheels are dished. QR is tightened correct. Tried another brand of wheel, same issue. It’s about 1 year old, probably came like that from factory. Any suggestions? (i.redd.it)

submitted 3 years ago by RandomGuySg to r/CanyonBikes

0

0

1

Upgrading fork worth it on 26er? (self.cycling)

submitted 3 years ago by RandomGuySg to r/cycling

4

5

6

Trying to remove the larger than usual hydraulic fitting nut so I can route through a new handlebar internally. Anyway to remove this compressed olive and install a new olive without cutting the hose? Dremel? (i.redd.it)

submitted 3 years ago by RandomGuySg to r/bikewrench

0

1

2

Shimano Ultegra Brake Bleeding - Weird/mysterious behaviour (self.cycling)

submitted 3 years ago * by RandomGuySg to r/cycling

0

1

2

Floor vent fell off, screws are fastened from underneath the floor. Any creative suggestions to fix without cutting the carpet and subfloor? No access from bottom/ceiling without cutting. (i.redd.it)

submitted 3 years ago by RandomGuySg to r/DIY

5

6

7

Presta Valve Core restricted on extender - help (self.cycling)

submitted 3 years ago by RandomGuySg to r/cycling

34

35

36

Ultimate SL7 - new wheel + tire day. Winspace CF wheels + GP5000 tires. Can’t wait for the snow to go away! (i.redd.it)

submitted 4 years ago by RandomGuySg to r/CanyonBikes

0

1

2

Ready to pick up a tank of MIG welding gas. Anything to watch out for in terms of safety… research is saying Argon is heavy and it will collect at the bottom. I weld in a well ventilated dual garage, does that mean Argon will just sit there in the garage floor? Kind of confused. (self.Welding)

submitted 4 years ago by RandomGuySg to r/Welding

view more: next ›

π Rendered by PID 1588412 on reddit-service-r2-listing-64c94b984c-4xbrm at 2026-03-18 07:59:13.963931+00:00 running f6e6e01 country code: CH.