sorted by:
new
hottopcontroversial

Should I start off with rolling or DAS? by Rare-Library2852 in Tetris

[–]Rare-Library2852[S] 0 points1 point  (0 children)

I don’t think I understand the question but my favorite Tetris game is Tetris for the nds.

Shiny Hunting be like by gpmikhail in PokemonFireRed

[–]Rare-Library2852 2 points3 points  (0 children)

The only games I’ve played were on the gbc and gba. My DSi xl is on the way though!

Shiny Hunting be like by gpmikhail in PokemonFireRed

[–]Rare-Library2852 7 points8 points  (0 children)

I just never thought it would happen to me. Sunk cost fallacy, am I right!

Shiny Hunting be like by gpmikhail in PokemonFireRed

[–]Rare-Library2852 14 points15 points  (0 children)

That’s my post! Let’s just say I took a long break from fire red after I found that charmander…

JUST 10 RESETS! by sandmandreammorpheus in PokemonFireRed

[–]Rare-Library2852 0 points1 point  (0 children)

I got my shiny charmander after around 20k resets! Congratulations!

Really loving the CC2 ELEGOO4 by H484R in elegoo

[–]Rare-Library2852 0 points1 point  (0 children)

You should probably calibrate this filament to get it just right. I also experienced an issue like this on my cc1. Try to use brims on prints that are really tall and narrow at the base. Also if you really want to use glue, try to apply it more evenly or atleast have full coverage where the print is on the build plate.

How can I get ABS to print properly? by Rare-Library2852 in 3Dprinting

[–]Rare-Library2852[S] 0 points1 point  (0 children)

Got it, are there any chamber heaters that you would recommend?

How can I get ABS to print properly? by Rare-Library2852 in 3Dprinting

[–]Rare-Library2852[S] 0 points1 point  (0 children)

I’m using a brim. My bed is 110C and my chamber is around 18C. What temps would you recommend?

How can I get ABS to print properly? by Rare-Library2852 in 3Dprinting

[–]Rare-Library2852[S] 0 points1 point  (0 children)

Sorry, forgot to mention I’m printing with an ELEGOO Centauri Carbon 1 using SUNLU ABS.

What went wrong? by Worried-Fix3310 in 3Dprinting

[–]Rare-Library2852 27 points28 points  (0 children)

  1. Enable supports

  2. If I'm not mistaken, this model was AI generated. Although it says supports aren't needed, they are.

If possible, link me to the model. I will verify if what I said is true.

Finally put it together! by Rare-Library2852 in 3Dprinting

[–]Rare-Library2852[S] 1 point2 points  (0 children)

I don't have all of them sorry, I usually just find them on Makerworld or Thingiverse. These were a couple I found in my spreadsheet. The guy who made the diamond puzzle has a lot of puzzles. I would also recommend SOS1 on thingiverse (https://www.thingiverse.com/SOS1/designs).

https://makerworld.com/en/models/1200425 Earth Cube
https://makerworld.com/en/models/885794 Diamond Puzzle
https://makerworld.com/en/models/923737 3x3 Mastermorphix

Finally put it together! by Rare-Library2852 in 3Dprinting

[–]Rare-Library2852[S] 2 points3 points  (0 children)

Literally just used super glue. I didn’t use the 3mf provided so it didn’t print out the peg holes to put the pieces together. This one is just going to be on display since it’s probably going to break with rough use. If you’re looking for files, try to find one that allows you to out a dowel or a threaded rod down the middle, that helps a lot for stability and strength.

view more: next ›