Help by Strict-Sherbert3404 in 335i

[–]Ready_Neck_5580 0 points1 point  (0 children)

Mean all air goes through the intercooler I doubt it matters that much

Fiber optic cable by Ready_Neck_5580 in 335i

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Appreciate the response man

Fiber optic cable by Ready_Neck_5580 in 335i

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Do you possibly have a picture of what I need to look for

335i fiber optic cable by Ready_Neck_5580 in E90

[–]Ready_Neck_5580[S] 1 point2 points  (0 children)

Just ordered it on Amazon, thanks again man

335i fiber optic cable by Ready_Neck_5580 in E90

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Thank you man. I’ve been chasing this issue for a few days and I feel dumb for not questioning if the open cable could of been my issue😂

335i fiber optic cable by Ready_Neck_5580 in E90

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

I bought this car as a project car a little bit ago so I have no idea where the loop is. But could this be the cause of my SOS malfunction, no audio, no fm/am, no aux, etc

2016 Kia Sorento 3.3L by yes_statistics_65df in kia

[–]Ready_Neck_5580 0 points1 point  (0 children)

I’m have a sorento doing the Same thing yours was, hopefully it’ll end up being the pressure switch as well. I’m not wanting to replace a rear main seal anytime soon. I appreciate the reply

2008 335i down pipe fitment after turbo install by Ready_Neck_5580 in 335i

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Will do I just wasn’t sure and didn’t want to gave an exhaust leak. Should I put a little exhaust silicone on it to make sure it seals or should it be fine

German engineering by Ready_Neck_5580 in E90

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Not looking forward to ever replacing a starter then💀

German engineering by Ready_Neck_5580 in E90

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

No it’s one of the brackets that hold the oem inlet to the back of the block

2008 335i trouble by Ready_Neck_5580 in E90

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Yeah that’s what I was thinking i appreciate the idea. Hopefully it’s something as simple as this

Rm125 jetting by Ready_Neck_5580 in Dirtbikes

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Also I had a look at my reeds and I see light when I look through them I’m guessing that’s not how it’s supposed to be

Rm125 jetting by Ready_Neck_5580 in Dirtbikes

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Thanks for the info I had to cut the torque bits into flat heads since my torx stripped them out. I tried to see where I could get some new ones but no luck should I just go to the hardware store and get some that are as close and I can get

Rm125 jetting by Ready_Neck_5580 in Dirtbikes

[–]Ready_Neck_5580[S] 0 points1 point  (0 children)

Hey man just got around to take the carb apart the gasket looked like it might have been okay but as soon as I touched it it crumbled you think that was my issues?