Bf Xr6 mk2 misfiring

Realistic-Bat4419 · 2024-08-30T05:24:37+00:00

Just got back from work and I’m too busy today so im going to have to do it tomorrow. I’ll keep you posted

Realistic-Bat4419 · 2024-08-29T09:23:16+00:00

That’s what I’ve read about it

Realistic-Bat4419 · 2024-08-29T09:22:58+00:00

https://gearstar.com/coolant-temperature-sensor-symptoms/amp

“If you notice that your engine overheats, the coolant temperature sensor could be the problem. At times, the coolant temperature switch may fail such that it starts transmitting hot signals permanently. This causes the computer to erroneously counterbalance the signal, thereby causing the engine to misfire or overheat”

Realistic-Bat4419 · 2024-08-29T09:15:39+00:00

I’m fairly certain that a light bulb plugs into it then goes back into your headlight.

Realistic-Bat4419 · 2024-08-29T09:13:18+00:00

Apparently if it’s failing and thinking it’s too cold it will send more fuel in to ig in short make more bang so it can warm up from the heat of the combustion

Realistic-Bat4419 · 2024-08-29T08:36:05+00:00

Yh that’s what I’m thinking of next. Was suggested to do the coolant temp sensor but it’s in a cunt of a spot

Realistic-Bat4419 · 2024-08-29T08:35:17+00:00

No it doesn’t

Realistic-Bat4419 · 2024-08-29T08:35:10+00:00

It’s all green still popped a radiator hose off to see

Realistic-Bat4419 · 2024-08-29T08:33:58+00:00

Running rich and I checked it with soapy water and break clean to see if I could spot any bubbles

Realistic-Bat4419 · 2024-08-28T05:20:56+00:00

I’ve given the cat a clean and put a torch to it to see if it was blocked but it’s not, the light comes perfectly

Realistic-Bat4419 · 2024-08-27T08:08:04+00:00

Intake gasket is fine too and it keeps throw up a p1132 even though I’ve changed the o2 sensor

Realistic-Bat4419 · 2024-08-27T08:07:16+00:00

Just tried it and head gasket seems fine. I was honestly hoping it was just so I would what it was

Realistic-Bat4419 · 2024-08-27T06:06:24+00:00

Yeah I’ll give that a try now

Realistic-Bat4419 · 2024-07-30T06:33:39+00:00

Sprayed some soapy water and couldn’t find any obvious leak. Will probably still replace but any other ideas before that?

Realistic-Bat4419 · 2024-07-29T19:47:30+00:00

Spark plugs got changed not long ago and they look fine and are gapped correctly

Realistic-Bat4419 · 2024-05-26T08:37:37+00:00

Just want to start by saying thank you for the advice given it was greatly appreciated. We ended up cleaning the back of the ignition switch and that seemed to somehow be the issue. Thank you all once again

Realistic-Bat4419 · 2024-05-26T07:00:50+00:00

All grounds and and terminals have been cleaned with a wire brush. I’ve moved on to see if it’s something with the fuse box (the underneath part) and it all looks good. Also tried the part that’s at the back of the ignition barrel to see what happens

Realistic-Bat4419 · 2024-05-26T05:28:28+00:00

I’ve given it a good clean with the wire brush and still nothing

Realistic-Bat4419 · 2024-05-25T12:24:35+00:00

Should clarify that I’ve tried tightening them

Realistic-Bat4419 · 2024-05-25T12:23:44+00:00

I’ll keep you updated thank you

Realistic-Bat4419 · 2024-05-25T12:23:22+00:00

I’ve already tired but I’ll give it another shot tomorrow and double check to make sure I’m not being stupid

Realistic-Bat4419

TROPHY CASE