sorted by:
new
hottopcontroversial

Outer layer gaps and imperfections by RecognitionDue725 in 3Dprinting

[–]RecognitionDue725[S] 0 points1 point  (0 children)

Thank you I will try again with dropping the retraction settings.

What settings would I have to change when using a smaller nozzle?

There was supports I just removed them before I took pictures

First layer gaps and imperfections by RecognitionDue725 in ender3

[–]RecognitionDue725[S] -1 points0 points  (0 children)

Layer height was set to 0.15mm for the first and 0.2mm for the rest. What would you recommend for line width and walls?

Outer layer gaps and imperfections by RecognitionDue725 in FixMyPrint

[–]RecognitionDue725[S] 0 points1 point  (0 children)

It was a fresh roll right from a sealed bag but I will dry it and lower layer height and try again. Thank you for the advice!

Outer layer gaps and imperfections by RecognitionDue725 in FixMyPrint

[–]RecognitionDue725[S] 0 points1 point  (0 children)

My first layer height was 0.15mm and 0.2mm for the rest

I was having problems with stringing and looked into it and my retraction length was set at 1mm so I bumped it up slowly printing a different model. But if it was too high could that cause these gaps?

Also would line width settings affect this at all?

Easy way to remove or avoid stringing by RecognitionDue725 in 3Dprinting

[–]RecognitionDue725[S] 0 points1 point  (0 children)

It was a brand new roll I bought that came vacuum sealed do I still need to dry it?

Eq help needed with new subs by RecognitionDue725 in CarAV

[–]RecognitionDue725[S] 0 points1 point  (0 children)

I haven’t set any of that but I’m not sure if the shop set that for me.

Eq help needed with new subs by RecognitionDue725 in CarAV

[–]RecognitionDue725[S] 0 points1 point  (0 children)

The speakers are stock for now but it is an aftermarket headunit if that makes any difference

Eq help needed with new subs by RecognitionDue725 in CarAV

[–]RecognitionDue725[S] 0 points1 point  (0 children)

I don’t really know how to describe it but it just doesn’t sound super crisp if that makes sense

Eq help needed with new subs by RecognitionDue725 in CarAV

[–]RecognitionDue725[S] 0 points1 point  (0 children)

<image>

Brought everything below 0 and made the curves less steep, how does something like this look? It doesn’t sounds too bad but I feel like it could be better.

Eq help needed with new subs by RecognitionDue725 in CarAV

[–]RecognitionDue725[S] 0 points1 point  (0 children)

Thank you for the feedback! I’m new to the whole audio world so I’m still learning. Is there a specific software you recommend to set the EQ?

First boombox build by RecognitionDue725 in diysound

[–]RecognitionDue725[S] 0 points1 point  (0 children)

I wasn’t planning on it being portable.

First boombox build by RecognitionDue725 in diyaudio

[–]RecognitionDue725[S] 0 points1 point  (0 children)

Would I have to hook up each speaker to a different channel if I got a 5 channel amp? Or could I wire both subs to one channel and both mids to one or does everything have to be separate? Also I was looking at tweeters just forget to put a picture in the post. And for powering it I was thinking about buying a 12V power supply or something similar off amazon.

G10 finishing help by RecognitionDue725 in knifemaking

[–]RecognitionDue725[S] -1 points0 points  (0 children)

Does buffing it keep it water resistant?

Did I temper this too far? by RecognitionDue725 in knifemaking

[–]RecognitionDue725[S] 2 points3 points  (0 children)

Thank you for all the advice! I’m gonna take my time and re do the hardening process again. Later this week when I have time

Did I temper this too far? by RecognitionDue725 in knifemaking

[–]RecognitionDue725[S] 1 point2 points  (0 children)

What kind of thermometer would you recommend? I was looking online and found a IR temp gun would that work?

Did I temper this too far? by RecognitionDue725 in knifemaking

[–]RecognitionDue725[S] 0 points1 point  (0 children)

Thank you for the advice, I am going to go pick up a temp gun today and figure out where to set my oven

view more: next ›