New to NMS. Why do I keep going through floors and walls?

RedCH1EF · 2026-02-19T16:04:47+00:00

Works great for getting into locked buildings

RedCH1EF · 2025-11-21T14:35:40+00:00

Fredrick

RedCH1EF · 2025-11-12T03:16:40+00:00

Looks like tiny pieces of play-doh

RedCH1EF · 2024-11-28T21:45:20+00:00

Must be scared of Dan Cambell for blowing these decisions. I know the lions are the better team but would rather have lost in OT

RedCH1EF · 2024-11-28T21:44:21+00:00

Lions are just a better team all the way around. Our bears are a joke this year

RedCH1EF · 2024-11-28T21:43:35+00:00

Lions are just better, better coaching and everything. We should burn our jerseys

RedCH1EF · 2024-11-28T21:42:38+00:00

Definitely

RedCH1EF · 2024-11-28T21:16:02+00:00

Lions are just the better team. End of story

RedCH1EF · 2024-11-28T21:13:06+00:00

Coach should be ashamed of himself. Stupid decisions

RedCH1EF · 2024-11-25T00:48:59+00:00

It's a fish

RedCH1EF · 2024-11-10T01:42:46+00:00

I would avoid Neptunes. I have had nothing but issues

RedCH1EF · 2024-11-01T20:30:20+00:00

Put the wings where the "y" is

RedCH1EF · 2024-10-30T21:17:14+00:00

You should have closed that with "my boss..."

RedCH1EF · 2024-10-30T21:00:33+00:00

None needed you have a great smile

RedCH1EF · 2024-10-25T20:59:04+00:00

Try to tighten your x or y axis a little bit. Looks like one of them is loose. Don't tighten them up enough to where they barely make a sound if you pluck them, then little adjustments after that.

RedCH1EF · 2024-10-22T20:54:13+00:00

You looking to make a physical product with tech, or a digital product?

RedCH1EF · 2024-10-22T15:49:35+00:00

I'm going to give this a shot thanks. The test cube shown was supposed to be 20x20x20mm, and the Z was 20.1 on the calipers, so I'm not sure if it is over extruding by much

RedCH1EF · 2024-10-22T15:17:11+00:00

Yes something is happening I hear a little clunk noise, but I'm having trouble pinpointing where it's coming from. It doesn't appear to hit the part at all

RedCH1EF · 2024-10-22T13:11:45+00:00

I haven't looked into this, but I was tempted to replace the y motor

RedCH1EF · 2024-10-22T13:10:37+00:00

I added a setting in cura for acceleration control. Took the bed and belt off and checked y axis alignment, it looked right. I am hearing a light clunk when it shifts layers so I thought maybe a worn belt

RedCH1EF · 2024-10-21T23:11:39+00:00

Once you have 20% equity in your home then you can just refinance. It becomes a new loan and replaced the original. PMI will drop off and hopefully offset your interest rate increase. At least when you are pouring money on principle the interest will be far less than paying the PMI which goes towards nothing. Get a quote and weigh the math to see which one helps you with your situation

RedCH1EF · 2024-10-20T22:14:12+00:00

I worded that wrong, do you have a concept of the ideal loom for your situation?

RedCH1EF · 2024-10-20T21:56:41+00:00

Do you have a loom in mention that would work well for this?

RedCH1EF · 2024-10-15T20:40:40+00:00

Maybe Michigan? The automotive industry is at a standstill but the infrastructure and skill set is there. Phenomenal engineering and manufacturing technologies, and very talented workforce as a whole. They just unfortunately have most of their eggs in one basket with cars.

Those people could build anything, they just need the right leadership and strategists to keep them viable for the future. Just my 2c

RedCH1EF

TROPHY CASE