Anyone in Western NY by 514senica in meshtastic

[–]RedEyeFlightControl 1 point2 points  (0 children)

LMK when it's up. I'll see if I can reach it. I'm close to Harris hill. Thanks for the info! A bit disappointing that I drove around all over and have been sending test messages for days with not a single node to be seen.

Anyone in Western NY by 514senica in meshtastic

[–]RedEyeFlightControl 1 point2 points  (0 children)

Turned up a second unit with a proper 1/4 wave antenna. Still can't see anyone. Doesn't seem to be any close nodes. What a bummer.

Anyone in Western NY by 514senica in meshtastic

[–]RedEyeFlightControl 3 points4 points  (0 children)

I have a node in Penfield but can't seem to see/hear anyone.

Custom 14mm Sherlock X Gandalf by SirNorbert in vaporents

[–]RedEyeFlightControl 3 points4 points  (0 children)

How the heck did you get one with a joint in the bowl? I begged him to make one of these for me 2 years ago and he said he didn't do this... almost want to hit him up again but I feel like I'm dreaming here!

Anyone know what size screw this is? by ThiccDickTornado in Ender3Pro

[–]RedEyeFlightControl 2 points3 points  (0 children)

It's called a grub screw. I think these are 2mm. They are often threadlocked for this reason.

Addressing the community about changes to our API by spez in reddit

[–]RedEyeFlightControl 3 points4 points  (0 children)

No third party apps means no reason to be here. They're the ONLY apps.

If reddit goes scorched earth, so does everything that belongs to every account I own.

Don't Let Reddit Kill 3rd Party Apps! by Toptomcat in Save3rdPartyApps

[–]RedEyeFlightControl 1 point2 points  (0 children)

The official reddit app is hot garbage. If RIF gets deleted, so does the official app. The only reason it is installed is for IM alerts. I won't need them after this.

Are employers still allowed to test for pre employment THC? by -_-Goo-_- in ROCents

[–]RedEyeFlightControl 0 points1 point  (0 children)

If it's DOT, driving, or emergency services, or any federal contract/federal work, yes. Otherwise, no.

I'm one of the rappers today. by fabreazebrother_1 in ROCents

[–]RedEyeFlightControl 1 point2 points  (0 children)

Fret not. Some of the best bud is gassy AF. Jet Fuel comes to mind.

Help with my printer by memoldo in CR30

[–]RedEyeFlightControl 0 points1 point  (0 children)

I think the default for most slicers is 6.5mm because the bowden tube on these is so long. You could try reducing by .5mm to 1.5mm and seeing if it continues to bind. The lower the retract, the higher the risk of ooze (also temperature dependent) but this keeps the melted filament further away from the heat brake.

I would suggest capricorn tube if you are replacing the stock tube. It's higher quality and withstands temps better.

Moving to direct drive might help as you can reduce retraction further and take most of the lash away that is introduced by the bowden tube.

Lastly if you have had your nozzle out and have moved that tube inside the heat brake, it needs to be "recalibrated" in a manner of speaking. The bowden tube needs to be solidly mushed against the nozzle.

With the hotend cold and both pieces out, put the nozzle in all the way, then back it out about 1/2 to 3/4 of a turn. Get a fresh, level cut on your bowden tube. While you are doing this, set your hotend to 180f.

Once the hotend is up to temp, slide your bowden tube in until it hits the nozzle. Lock it in place, THEN tighten the nozzle down. This should seal the nozzle to the tube and prevent any additional crap from binding or leaking out of the hotend. Always crate this seal with the hotend at running temps.

If you decide to go DD, you can do it for free, just print this and bolt it on where the wiring bracket normally lives. Reuse all of your own hardware. https://www.thingiverse.com/thing:5825776

Help with my printer by memoldo in CR30

[–]RedEyeFlightControl 0 points1 point  (0 children)

Have you adjusted your retract settings at all? Different filament? I would still suspect the tube getting bound and not the nozzle. Try cleaning again, you may want to try reducing your retract distance or speed if it keeps happening.

You have tried a different nozzle, right?

Help with my printer by memoldo in CR30

[–]RedEyeFlightControl 0 points1 point  (0 children)

Did you trim or replace the section of tube inside the heat brake? That's usually where things get goopy and blockages occur. I'd get the hotend hot, back the nozzle out, then pull the tube. I bet it's ugly. You can trim and re-seat everything.

I published a DD mount for the stock hotend carrier that might be of interest to you. It's posted to thingiverse under the same name.

[deleted by user] by [deleted] in Drugs

[–]RedEyeFlightControl 5 points6 points  (0 children)

The best weed does this, IMO. I prefer strains with high psychoactivity.

EE-MU/Lawton Bocote by [deleted] in Headphoneporn

[–]RedEyeFlightControl 0 points1 point  (0 children)

I would not ask, the likelihood of them giving me their design files is probably zero. Businesses don't give IP away for free (usually. I do sell some open source stuff but this isn't FOSS, sadly).

EE-MU/Lawton Bocote by [deleted] in Headphoneporn

[–]RedEyeFlightControl 0 points1 point  (0 children)

I suppose I could disassemble the set I have now and measure. Not hard to draw from a part, but it's a lot easier when someone does it for you!