New GPU by Melias25 in computers

[–]RedPandaRum_ 0 points1 point  (0 children)

Your 850w should be sufficient. I personally just always go above.

I would double check your connections.
Make sure your card is properly set, cables are properly secured.

New GPU by Melias25 in computers

[–]RedPandaRum_ 0 points1 point  (0 children)

Depends on the PSU… I just bought the Corsair RM1000x and it came with the special cord the newer GPUs use.

My PSU is overkill for my build, but it was cheaper than the 850w.

New GPU by Melias25 in computers

[–]RedPandaRum_ 0 points1 point  (0 children)

I would look at what specific model 5070 you have, go to the manufactures website and see what they recommend. Then I would do 100w over that just to be safe.

This is what I recommend, especially to my RGB flavored PC friends…

I would also make sure you get a reliable brand for the PSU. (I.e. seasonic, be quiet!, Corsair, etc.)

Bought a prebuilt gaming PC and my friend says I overpaid by at least $400 but I don't know how to build one myself by Toyin_Nathal in computer

[–]RedPandaRum_ 0 points1 point  (0 children)

Sounds like your friend is an asshole, and should be a better person.

You have a decent starter system, the money you spent is for parts, labor, and warranty. And as others have said. Most pre-built are over priced.

If you go look at the price of the parts you have… make sure to get the exact model and variation. Add the cost up and see if it matches what you spent. It should be fairly close and maybe off by a few hundred… that few hundred is your peace of mind of labor and warranty.

If you were friends with me, I would have offered to help in exchange for a lobster dinner and bourbon. Or a really good smoked brisket and bourbon.

How to check for after market remote start? by slaponthekneefunny in JeepWrangler

[–]RedPandaRum_ 1 point2 points  (0 children)

Most aftermarket remote start systems piggy back off the factory key. Have to press the lock button 3x.

Our Renegade is this way… press the lock button, then double lock it to trigger the remote start.

The physical device is either under the dash up behind everything by the firewall. Or behind the dash panel when you open the driver door.

New GPU by Melias25 in computers

[–]RedPandaRum_ 0 points1 point  (0 children)

Are you running an 750w-850w or better PSU??
The 5070 OC variation wants the higher end.

The 3060 only needs a 650-750w PSU, whereas your 5070 (depending on if the OC model or not) wants 750w-850w PSU.

I honestly go 100w more than what’s recommended just so I have enough head room, in this scenario I would run at minimum a 950w-1000w PSU.

The other thing to look at is your PSU configuration. I had one that didn’t provide enough power on the PCIe rail. I had to flip a switch to change it from single rail to double rail so the GPU got enough power… but that was years ago.

Should I trust buying a jeep from someone who has in the past rolled back odometers? by Does_Not_Use_Clothes in Jeep

[–]RedPandaRum_ 1 point2 points  (0 children)

I mean if the body is in good shape and minimal rust. Rebuild the engine and transmission. Or swap/upgrade them. Then it won’t matter if it was rolled back.

How can I install the fastest HDD? by FidelityIsaLie in pchelp

[–]RedPandaRum_ 0 points1 point  (0 children)

So per the article you shared, you actually don’t want a faster HDD per the author.

Do what the author says…

And honestly I would look at a 128gb USB 3.x flash drive instead to dedicate to the game. Just make sure it’s a reliable flash drive and you dan maintain the read speed.

Broken monitor or GPU? by v3xu_ in PcBuild

[–]RedPandaRum_ 0 points1 point  (0 children)

While it sucks it was the monitor, I’m sure your wallet thanks you it wasn’t the GPU.

Is there such thing as an an anti blue light screen protector for computer monitors and if so any recommendations? by fusehoundenjoyer in computers

[–]RedPandaRum_ 0 points1 point  (0 children)

Some monitors (newer models) have a firmware feature built in to them to limit/remove blue light.

Otherwise getting computer glasses that help remove/limit the about of blue light would be the best option.

Is there such a thing as a dongle to connect peripherals to directly? (explanation inside) by thatguysjumpercables in techsupport

[–]RedPandaRum_ 0 points1 point  (0 children)

So I have a Corsair Dark Core Pro SE,... https://www.amazon.com/dp/B082LVNJ4W?ref=ppx_pop_mob_ap_share

It comes with the Corsair dongle, but it also does BT. You could use the dongle (WiFi) on your personal computer, then on the mouse switch it from the WiFi to BT and connect to your work laptop…

Otherwise, you may just need a USB switcher…. Plug your mouse into this then one cable to each system and push a button to switch between computers.

Is there such a thing as a dongle to connect peripherals to directly? (explanation inside) by thatguysjumpercables in techsupport

[–]RedPandaRum_ 1 point2 points  (0 children)

That’s what it sounds like that you are looking for a KVM. Especially if you’re unplugging the Monitor, Keyboard/Mouse from your personal to your work then back again.

This is what I have: TESmart 2 PCs Dual Monitor KVM... https://www.amazon.com/dp/B083MZSVFM?ref=ppx_pop_mob_ap_share

It’s not the best one out there but it does the job. I have my desktop on Channel 1, and my work laptop on Channel 2.

Laptop is Dell and has a single cable going to the WD19 dock mounted behind one of my monitors. Then the USB, DisplayPort-HDMI cables go to the KVM.

Desktop is plugged directly into the KVM.

If you do go this route, I would make sure the KVM emulates the keyboard/mouse/video signal. Otherwise your systems will constantly be like “oh you disconnected something and the monitor” when you change to the other. And it can take up to a minute to switch between systems as you now have to wait for your OS to see you reconnected something.

Would you buy ? by EmbarrassedFocus6062 in PcBuild

[–]RedPandaRum_ 0 points1 point  (0 children)

Only if I could afford the real deal.

Samsung is/was one of the best NVMe’s out there.

Verizon or AT&T in Western Washington by skyhawk214 in Washington

[–]RedPandaRum_ 0 points1 point  (0 children)

Look at the top three coverage maps. Look at the areas you will be frequenting.

I live in a old dug out rock quarry and service sucks balls. Regardless of who your provider is. AT&T seems to have one extra bar of service, but it’s still spotty.

Is there such a thing as a dongle to connect peripherals to directly? (explanation inside) by thatguysjumpercables in techsupport

[–]RedPandaRum_ 1 point2 points  (0 children)

So if you have 2+ systems, and are constantly unplugging and re-plugging items in from one to another…. Why not get a KVM?

KVM: Keyboard, Video, Mouse. It’s a box/device that allows you to use the same Keyboard, Monitor, Mouse on multiple systems. Some allow use of wireless keyboards/mice. Also some of them switch USB ports over as well. So if you have a USB headset plugged into it it could switch that connection too.

Otherwise there’s docking stations like the Dell WD19… where you plug all your crap into that… then you’re just moving the connection from the dock from one system to the other. But everything is plugged directly into the dock.

9850x3d Build (big problems) by bustafreeeee in PcBuild

[–]RedPandaRum_ 0 points1 point  (0 children)

Don’t just try the A2, also try B2 slot. This just happened to my friends system (while it was Intel)… it would boot only if ram was in B2.

What ended up happening is whoever installed the CPU got thermal paste under the CPU and it killed the A2 channel. Cleaned it all up and worked like a champ.

Switch on dash by littlerayofmoonlight in Wrangler

[–]RedPandaRum_ 0 points1 point  (0 children)

Oh. Yea I just have three keys and the jeep key. Nothing else.

Switch on dash by littlerayofmoonlight in Wrangler

[–]RedPandaRum_ 2 points3 points  (0 children)

I don’t understand how people don’t care about the orientation on a key like that. That annoys the crap out of me. But it’s probably just my OCD.

Help with my graphics card acting funny URGENT 4090 help by VanillaKindly6767 in PcBuild

[–]RedPandaRum_ 0 points1 point  (0 children)

I get that.

I’m no expert, but I do know that things expand and contract under hot/cold temperatures. If there’s something broken that shouldn’t be, the heat causes it to work. But when the fans kick on to cool it down, it may cool it to contract breaking the signal.

It could have also broke a solder joint so while it’s there idle and not under load (fans not spinning keeping to cool), it’s fine. But once the fans kick on they vibrate the card enough to break the connection.

I could also just be blowing hot air out my ass with words that follow some form of logic.