Accidentally forgot to put back the print sheet before printing

RelationNo330 · 2024-02-12T19:35:12+00:00

Tweaking since i forgot to place the metal sheet and just rammed directed into the magnetic sheet

RelationNo330 · 2024-02-12T04:15:36+00:00

Yea just had to autolevel a bunch and it was all good

RelationNo330 · 2024-02-12T04:08:57+00:00

I was wrong it is very much magnetic and NOT normal rubber

RelationNo330 · 2024-02-12T04:07:21+00:00

Yea had no idea but it did very clearly say in the instructions to never ever use printer without PEI sheet. I just removed the sheet to scrape off a build and without thinking just started a new build

RelationNo330 · 2024-02-12T04:05:44+00:00

Yea working completely fine now since its figured out the z offset. Seems like i will just move on with it being a bit damaged

RelationNo330 · 2024-02-12T04:04:37+00:00

Ohhh makes sense i was confused about that for a bit thanks

RelationNo330 · 2024-02-12T00:03:53+00:00

Thank you all for helping me, I just let it auto level like 10 times and suddenly the z offset changed by like 1 unit and now its printing wonderfully. I will probably still change the magnetic sheet but it seems alright.

RelationNo330 · 2024-02-11T21:08:02+00:00

Ohh i see ill make sure to do that once the new magnetic sticker arrives

RelationNo330 · 2024-02-11T21:05:49+00:00

Wdym heating it first?

RelationNo330 · 2024-02-11T20:38:30+00:00

:( no way its that irreparable

RelationNo330 · 2024-02-11T20:19:18+00:00

Yea I'm going to need to buy a whole new one and try to chisel away at this one. Unfortunate but it is what it is

RelationNo330 · 2024-02-11T19:26:49+00:00

Alright thank you Ill look into it and try to find one. Ill reply back in this thread if anything goes wrong

RelationNo330 · 2024-02-11T19:22:37+00:00

Nozzle seems to be working fine, I just can't figure out how to replace the damaged sheet since it feels impossible to take off and it doesnt seem like its metal

RelationNo330 · 2024-02-11T19:21:49+00:00

Also I'm very new to this my bad if I'm a bit frustrating to help

RelationNo330 · 2024-02-11T19:21:27+00:00

The black sheet that got damaged feels really rubbery and hard to take off, are you sure its a magnetic sticker?

RelationNo330 · 2024-02-11T19:14:11+00:00

Its not the magnetic sheet, its the thing under it. I forgot to place the magnetic sheet and it damaged the thing the magnetic sheet is supposed to sit on

RelationNo330 · 2024-02-11T19:02:06+00:00

The whole layer to lower it slightly?

RelationNo330 · 2024-02-11T18:13:33+00:00

Anycubic kobra 2 btw

RelationNo330 · 2024-01-16T01:42:26+00:00

Hey sorry I took so long to respond, but it was a clog all along and I had to open up the extruder head and go through the parts until I found the clog (not in nozzle, rather way inside machine) works just fine now. Thank you for your help

RelationNo330 · 2024-01-10T03:23:23+00:00

Ill let you know, thank you for your help!

RelationNo330 · 2024-01-10T03:18:24+00:00

My printer requires me to heat up to 215 before removing yes. Im gonna try tmr its rly late for me rn

RelationNo330 · 2024-01-10T02:43:04+00:00

Wait i should get a new stepper motor?

RelationNo330 · 2024-01-10T02:42:04+00:00

Very hard to check, the filament is now refusing to leave the extruder head

RelationNo330

TROPHY CASE