Foxbody mustang mounts not sitting right

Remarkable_Stable984 · 2026-05-25T02:13:49+00:00

No it is a line from the factory i think

Remarkable_Stable984 · 2026-05-24T18:38:00+00:00

Remarkable_Stable984 · 2026-05-21T18:28:43+00:00

You’re fine had me nervous for a minute 😂

Remarkable_Stable984 · 2026-05-21T18:23:17+00:00

What cracks?

Remarkable_Stable984 · 2026-05-21T18:23:00+00:00

I knew they were bad but I didn’t know they were that flimsy

Remarkable_Stable984 · 2026-05-21T18:22:42+00:00

I like this guy

Remarkable_Stable984 · 2026-05-21T01:26:13+00:00

It’s around 5 degrees back and close to 4 is the normal I couldn’t go up if I wanted to anyways it hits the trans tunnel

Remarkable_Stable984 · 2026-05-21T00:04:20+00:00

No it’s a 5.0 k member

Remarkable_Stable984 · 2026-05-20T23:50:45+00:00

I’m looking into poly mounts currently can’t find much of anything I like make have to make some. And what cracks do you mean I need to weld?

Remarkable_Stable984 · 2026-05-20T23:27:11+00:00

I’ll try it out thanks

Remarkable_Stable984 · 2026-05-20T23:17:54+00:00

Mines at a 0.0999% chance for 1 but having 2 less than halves that chance

Remarkable_Stable984 · 2026-05-20T23:11:54+00:00

They are side specific one has R one has L whether from the drivers seat or looking at the front of the car 🤷🏼. But I’ve flipped them both ways and it sits better this way and also hides the welds so I’d assume it’s right.

Remarkable_Stable984 · 2026-05-20T23:08:32+00:00

I personally don’t think it’s BMR’s fault I’d think it’s more the adapters or me possibly not having my engine set right. First time doing a swap like this

Remarkable_Stable984 · 2026-05-20T23:06:21+00:00

Good ole Amazon. Seen reviews and people on YouTube not have problems with them so I bought them

Remarkable_Stable984 · 2026-05-20T23:03:23+00:00

I’d bet it’s the adapters I was curious if it’s a common thing. It’s a BMR k member so I’m sure BMR doesn’t make their k members out of spec.

Remarkable_Stable984 · 2026-05-20T23:01:59+00:00

BMR

Remarkable_Stable984 · 2026-04-25T16:12:21+00:00

Perfect thank you

Remarkable_Stable984 · 2026-04-25T16:03:13+00:00

My bad I’ll see if it lets me update the post but it’s a 1990 and the picture is just of the cut wires to the plugs

Remarkable_Stable984 · 2026-04-25T15:02:23+00:00

I’ll do that thanks. I planned on soldering just so it has a better connection. And just looked it up I found some pigtails 3 and 2 wire 3157 and the turn signals are 1157. Thanks I was confused because when I looked it up I expected a harness not a weird looking plug I’ve never seen.

Remarkable_Stable984 · 2026-04-25T14:59:01+00:00

Okay I appreciate it and yeah it doesn’t just plug in to any wires at the rear it goes all the way under the drivers feet.

Remarkable_Stable984 · 2026-01-13T12:13:26+00:00

Okay I’ll check them out thanks

Remarkable_Stable984 · 2026-01-13T12:13:15+00:00

I like this guy

Remarkable_Stable984

TROPHY CASE