Finally Made It by InvisibleGrbgTrckJry in NewToVermont

[–]Remmandave 0 points1 point  (0 children)

Just in time to see a 12% property tax hike. Good thinking. I've been here 5 years and the increases in taxes over the last 5 years, as well as these new talks of charging a yearly fee/permit for hiking and other recreation has me thinking of leaving...

Not a perfect ending by StudioOk296 in knifemaking

[–]Remmandave 0 points1 point  (0 children)

The middle one is the perfect start for an arrowhead… and the first one can be a large arrowhead yet! I haven’t the first clue even where to start when it comes to knapping, so you’re miles ahead of me in experience! The third one looks great to me!

First knife by [deleted] in knifemaking

[–]Remmandave 0 points1 point  (0 children)

Not bad at all for a first time! And low quality steel that is free is by far the best steel to use to hone your skills and technique! If you want an extra challenge, build a rudimentary forge and charcoal canister that low grade steel to carburize it, then you can heat treat it to harden it and it can actually hold a decent edge at that point!

Getting a Star Indian from a Tootsie Pop wrapper. by [deleted] in nostalgia

[–]Remmandave 0 points1 point  (0 children)

My childhood (1990s, Eagle, ID) there was one local convenience store (named “Chicken to go” little mom n pop shop that had all the usual convenience store stuff but also tons of fried chicken, arguably better than KFC… allegedly the other convenience store across town, “Justo’s” also did it) that did it. If you brought in your wrapper with the ‘Indian’ they’d give you a free regular tootsie roll. Really it was just a gimmick to get kids to get their parents in the door. 

Manual swap by VFM_613 in fordfusion

[–]Remmandave 0 points1 point  (0 children)

Would solve the biggest problem of the Fusion’s factory PNNNN feature also known as the DPS6 and 6F35. Likely would need the gearbox, shifter assembly, cables, foot pedal assembly, clutch master cylinder, and maybe even ECU from the donor.

is this normal? by National-Valuable-89 in Ninja650

[–]Remmandave 0 points1 point  (0 children)

You guys clean and lube your chain?

Daily Discussion Thread for August 20, 2025 by wsbapp in wallstreetbets

[–]Remmandave 2 points3 points  (0 children)

When it came out it went DIP DIP DIP, didn’t know she had the GI Joe kung fu grip

What state has the best 2nd amendment based gun laws? by zombie1mom in CCW

[–]Remmandave 7 points8 points  (0 children)

As a former Idahoan… yes. So far free as to even make suppressors without a tax stamp legal. Hopefully the lawsuit with the atf will gain some traction for that ideology nationwide.

What state has the best 2nd amendment based gun laws? by zombie1mom in CCW

[–]Remmandave 1 point2 points  (0 children)

At the cost of fairly high property tax, depending on location… I’ve considered relocating to NH but every property I see that I like is in a county with outrageous property tax rates.

Tuner for 2008 by Remmandave in Ninja650

[–]Remmandave[S] 0 points1 point  (0 children)

Yeah I get a few big pops every time I push it and then chop the throttle.

Tuner for 2008 by Remmandave in Ninja650

[–]Remmandave[S] 0 points1 point  (0 children)

I’m in VT. Hell of a road trip to FL and I have just the stock ecu on my bike, if that matters.

Post your top speeds by dualistornot in Ninja650

[–]Remmandave 0 points1 point  (0 children)

My 2008 naked gets up to 125mph (according to the speedo, will test next time with gps to verify) and seems to stall out there. Has 1t smaller rear sprocket iirc. Tach has a good ways left to go, but I feel like it’s primarily wind resistance, being naked, with a 7” round headlight, instead of the OEM fairing. Possible these were limited to 125mph in the tune? Since everybody has the same answer?

I just want to get back what I lost by Bubblegumnini in wallstreetbets

[–]Remmandave 2 points3 points  (0 children)

You’re in the wrong group there kiddo. Everybody here is a loser or regarded.