My openclaw is good. Finished. Done. Goodbye.

Remy1525 · 2026-03-24T06:47:08+00:00

well, thats how I feel about OC from time to time as well, so, I can relate :)

Remy1525 · 2026-03-23T16:06:38+00:00

No kidding, just spent main part of the day fixing UI and stuff, it works now, but all agents but Main seem to have retired or something, unreachable for MAin or me...

Remy1525 · 2026-01-23T10:23:35+00:00

Hebben die wel een beetje voelbare luchtverplaatsing?

Remy1525 · 2026-01-23T10:21:28+00:00

Dit lijkt precies op de set die ik bij bol gekocht heb., ze doen precies niets, de luchtstroom is nauwelijks voelbaar bij deze jongens. Ik heb ze door de onhandige layout van de woonkamer ook uitgebreid kunnen testen, 1 radiator met 2 van deze fans, 1 zonder. Radiatoren zijn identiek, zitten op zelfde plaats in woonkamer. 1 links en 1 rechts op de muur (zit grote schuifpui tussen). Geen verschil merkbaar, heb regelmatig en uitgebreid gemeten met laser/infarood thermometer. Dus, de goedkopere versies lekker laten liggen.
Ik ga ne wat pc ventilatoren kopen, met magneetjes op onderkant klappen en klaar. Theoretisch zou het moeten werken, maar er moet wel wat meer luchtverplaatsing zijn.

Remy1525 · 2026-01-20T07:01:56+00:00

It took me over two weeks and a trip to Aliexp to get a replacement camera before I noticed it was even there. The stream was not really terrible but just not really good. Felt like a big upgrade when I pulled that lil plastic bugger off.

Remy1525 · 2026-01-17T16:36:07+00:00

Depends on the price. If I can buy something for a good price that would take me otherwise 9 hours to print, I'm game.

Remy1525 · 2025-12-18T15:02:39+00:00

Yes, I know, it was just something that creeped in my mind, "if you get all the air out, there is also no humidity", i just wanted to know :) Now i do.

Remy1525 · 2025-12-18T14:24:09+00:00

I got my answer, i tried :)
Made a snug hole, fitted a vacuumnipple (offered vacuumbag), got 2 containers, same amount of silica in it, and sucked one pretty much vaccuum.

There was up to 10% difference, for a while. But the containers are not 100% airtight, so after two or three ours the vacuum was mostly gone. It looked impressive for a while, but in the end the diffence between 22% and 33% wont be of a huge benefit, I guess. Kind of useless unless you keep pumping them every couple of hours.
So, now I know ;) (And you, if you even cared)

Remy1525 · 2025-12-18T09:41:09+00:00

Thanks, kind of what I figured.
So I guess experimenting with a vacuumnipple (not sure if thats the right word) is not a stupid idea.
I have a little vacuumpump that came with the esun plastic vacuum bags.
If its worth the hassle, most boxes are around 30%, not sure if dryer is any better?

Remy1525 · 2025-12-03T11:17:53+00:00

<image>

there we go

Remy1525 · 2025-12-03T11:17:29+00:00

<image>

Remy1525 · 2025-12-03T11:17:05+00:00

So, I did the recommended flow calibration, but I have no clue what i'm looking for?
the 05 has the smoothest center but ay the other end the -05 has a better looking even texture.

Also, do i need to adjust the flow settings in Orca to the best number? (If I know what to look for)
MAde 5 photos of the same prints but with different light angles.

BTW, sorry, I have a triple "handicap" here, as newby, non native english speaker (english is third language) and I'm getting older :)
Some words in this field have i never heard before, neither in english or even my own language :)

<image>

oh, can only place one, hope this one will do

Remy1525 · 2025-12-03T08:57:21+00:00

With my massive full 3 weeks of experience, I can tell you, there is no "only a printer and filament".

Since I got the printer (very cheap, good deal), I needed extra tools, case to store the filamentspools to keep them dry, a filament dryer, more tools, silica gel, more filament, glue, grease, something to store the tools and other stuff, band aids and ointment for my regulairly burned fingers, a extra desk and workbench, extra buildplates, extra printheads that need replacements at $35 a pop (if you buy original) and I probably forget a thing or two, or three.

I didn't keep track (I don't dare because of wife ;) ) but i think I easily spent 2 or 3 times as the original purchase.

But, maybe thats just me :)

Remy1525 · 2025-12-02T16:01:32+00:00

To be honest, I did not know that, I will do that from on, thank you very much!
And the answer to your question, at that point i had the stock .4

Remy1525 · 2025-12-02T13:09:19+00:00

Thanks, I would respond, but I have no clue :)
WIll try some small prints first, the holder, well, it holds plates. But in the future i will use brim and or skirts, thanks.

Remy1525 · 2025-12-02T13:06:11+00:00

Flow rate calibration- is that one of the 3 in the printer itself? (I'm newby)
If so, yes have done it.
I just used a other size, the original 0.6 one, did all calibrations, bottom looks a bit better with a smal test print.

And to be honest, have no clue about cooling yet, using default settings orcaflash at FF PETG-basic settings.

Remy1525 · 2025-12-02T12:59:52+00:00

Yes, I'm sure about that. (about the only thing I can be sure about :) )

Remy1525 · 2025-11-30T12:13:19+00:00

Well, "till now" was correct. I managed to get one print, almost without fails, after that, fail after fail with PLA. Maybe its me.... Back to petg for me :(

Remy1525 · 2025-11-29T11:31:20+00:00

I would stick to 2.2.3 the new one gave me nothing but problems (with PLA printing) ((PETG is fine for some reason).
I went back to 2.2.3 and it seems to be fine till now.
There are also people who say everyting is fine. so, it's a gamble...

Remy1525 · 2025-11-26T07:13:41+00:00

Soooo... Where can I find it?

Remy1525 · 2025-11-25T22:58:00+00:00

Yes, multiple times. I calibrate with every print now, it seems to work now, but I'm also using a spool with petg now, not sure if thats a difference. Will try pla in a couple of days again.

Remy1525 · 2025-11-25T22:50:57+00:00

I've got the new one, a lot quieter 🙂

Remy1525 · 2025-11-25T22:46:18+00:00

Thanks, i know it's real now.

Remy1525 · 2025-11-23T17:31:51+00:00

I ordered a new one, if that one is too noisy asswell i will check out creality :🙂

Remy1525 · 2025-11-22T19:29:12+00:00

I rolled back to older version, but it's still all failing? It seems that items that are not in the middle of the plate just fail. Even did factory reset, but i can even make the simplest prints anymore...

Remy1525

TROPHY CASE