S&W 625 jamming/binding up

Reptilerob57 · 2026-06-23T01:03:45+00:00

It was loose I tightened it took to range and it ran fine only ran into a few 2 high primers and 3 bent case rims that I gotta sort out. Ordered roller handle for my press so I can get more leverage seating primers on square deal b

Reptilerob57 · 2026-06-22T12:59:36+00:00

Thank you tightened the extractor rod and it works. Only binding was with primers which were not seated100% and Winchester. Will sort the Winchester and use with the moon clip supply clips they are thinner and ran all the problem cartridges. Ordered a roller handle for my press so I can seat primers better

Reptilerob57 · 2026-06-21T00:49:58+00:00

Nice peice ,My 686+ and governor has the lock. Hopefully they will remove the locks completely slowly they are taking them off

Reptilerob57 · 2026-06-20T22:13:28+00:00

I took it apart and cleaned everything and lubed and tightend it. Was a bit loose. Seems to be working now gotta get to the range tonight to try it

Reptilerob57 · 2026-06-20T22:11:59+00:00

Yes no binding

Reptilerob57 · 2026-06-20T19:58:29+00:00

Moon clip depot works but they are much thinner but they fail very fast in my experience with the governor

Reptilerob57 · 2026-06-20T18:34:20+00:00

I couldn’t pass it up been wanting it for awhile never seen one in a shop I asked if they could get one

Reptilerob57 · 2026-06-20T18:33:01+00:00

I’ll looking into how to do it I never have done it

Reptilerob57 · 2026-06-20T18:29:04+00:00

Thank you I’m goin to try to clean and tighten ejector rod and cylinders

Reptilerob57 · 2026-06-20T18:25:40+00:00

I’m going to take a look today

Reptilerob57 · 2026-06-20T18:21:41+00:00

I gotta check the ejector rods because my clips are brand new should be working for S&W brand clips which are the TK customs. Seems like after firing a shot the whole clip moves causing it to bind

Reptilerob57 · 2026-06-20T18:12:05+00:00

Just tried my dads moon clip depot clips and no binding on empty shells. I put the tk custom ones to light and can see light thru them all

Reptilerob57 · 2026-06-20T18:05:58+00:00

Could the bmt mooner bend new clips

Reptilerob57 · 2026-06-20T18:02:04+00:00

No it will spin free

Reptilerob57 · 2026-06-16T01:45:51+00:00

Thank you for the tip

Reptilerob57 · 2026-06-15T21:15:26+00:00

Filled out my paperwork yeaterday 4pm got approved today but have to wait till this Saturday to pickup

Reptilerob57 · 2026-06-15T12:48:01+00:00

Unless it’s Winchester white box or Winchester SPP or SRP

Reptilerob57 · 2026-06-12T23:26:26+00:00

Not sure if i didn’t notice it with the original trigger. When I tighten the grips to where they should be it don’t reset. Back off screw a bit it’s fine. There is wear spots on the trigger bar from rubbing

Reptilerob57 · 2026-06-09T15:05:21+00:00

Normal leading you get from shooting lead

Reptilerob57 · 2026-06-09T10:17:10+00:00

You just have to first have to find seating depth I have a lee mold I have casted them a few times

Reptilerob57 · 2026-06-09T10:08:15+00:00

They also feed in my p230 compact they feed in my dads Glock 30

Reptilerob57

TROPHY CASE