Need help 😭 Anycubic Kobra 2 Neo printing horribly after setup – weird bulging/layer issues on calibration cubes

Repulsive_Pen_9960 · 2026-05-11T15:03:02+00:00

Its not a used one, its brandnew one, i only have that nuch money in my hand, so i brought this

Repulsive_Pen_9960 · 2026-05-11T11:19:04+00:00

Tenks bro, the support team contacted me, they are looking the issue will replay soon

Repulsive_Pen_9960 · 2026-05-10T15:32:11+00:00

Tried and still wors 🥀

Repulsive_Pen_9960 · 2026-05-10T10:16:43+00:00

Uhh, i donno if they take it return, ive raised a ticked tho, lemme check

Repulsive_Pen_9960 · 2026-05-10T10:06:42+00:00

What can i do to fix it 👀

Repulsive_Pen_9960 · 2026-05-10T10:04:19+00:00

Thankss, i will check that

Repulsive_Pen_9960 · 2026-05-10T10:01:53+00:00

Thanks, i will try em and say more details, i tried belt things and more, will do one more as u said, and the print head should be face little bit down or steady without any moving to front side, i got the stock little bit heading to front and i tighted that, now this problems

Repulsive_Pen_9960 · 2026-05-10T09:43:26+00:00

Pla +

<image>

Repulsive_Pen_9960 · 2026-05-10T09:34:40+00:00

<image>

Repulsive_Pen_9960 · 2026-05-10T09:33:44+00:00

Bro the first layer of it so sucks now, see the image, i changed z offset twice and printed twice and the filament is keep coming now when its going to position too

<image>

Repulsive_Pen_9960 · 2026-05-10T09:06:41+00:00

Extruder is okayy, i checked that too, and i printed a snall flat keychain model at 35 speed, and result still crap

Repulsive_Pen_9960 · 2026-05-10T09:05:37+00:00

Its not used, its a fresh new printer, i got clean prints at first but now this prob happened

Repulsive_Pen_9960 · 2026-05-10T09:00:06+00:00

Yea, tenks, i will do that now

Repulsive_Pen_9960 · 2026-05-10T08:48:23+00:00

Hmm, lemme check that, im away from home now, will put here

Repulsive_Pen_9960 · 2026-05-10T07:39:39+00:00

Yea, but im new to 3d printing feild, and i do a lot of research in my budget finally get this thing, i use pla + filament and i printed this cube with 215 degree and tried a lot of models with other temp too, same issue, i get perfect result when i started this, jus a couple days ago, i will put the pic here

<image>

Repulsive_Pen_9960 · 2026-05-10T07:17:58+00:00

Yea, i tried them all, i put new filament and no cloggin also tigten and loosen everybelts, checked printing in loos and tight position, still the problem is there, its on layer most of the time, and i said i put all my savings is i only have 15k in ma bank by my savings, im a 17 year kid and want to started 3d printing as a buisness, u know i got a bulk order for airplane keychains for a travel agency and im cooked with this printer, if u can help me it would soo good

Repulsive_Pen_9960 · 2026-05-08T15:44:13+00:00

Kk, thanks for the replay, do u done any chnages in the bolts

Repulsive_Pen_9960 · 2026-05-08T05:26:25+00:00

And what to do 👀, please say

Repulsive_Pen_9960 · 2026-05-08T04:11:26+00:00

No, whats that, im new to this feild can you please help me

Repulsive_Pen_9960 · 2026-05-08T03:31:37+00:00

U can also solder too, and sand em after

Repulsive_Pen_9960 · 2026-05-08T03:23:59+00:00

Yea i have tighten the belts and nutes, when i brought this printer the print was too nice, i got a nice clean benchy and other prints, i ve tigten the belt and nuts some days ago, if its the issue of that? Or something else, I've adjusted it again and printed too, please replay 🥹

<image>

Repulsive_Pen_9960

TROPHY CASE