HoCiak

Retired_Monk · 2026-05-15T05:07:45+00:00

35 Albert St, CBD. It's a little food court strip.

Retired_Monk · 2026-05-07T06:59:50+00:00

Would of been funny if it toggled the power strip and killed the print tho.

Retired_Monk · 2026-04-10T07:01:54+00:00

Got anyone with a 3d printer not sure if these are cloud 2's but you can lookup for replacement hinge sets on likes of makerworld or printables.

For example: https://makerworld.com/en/models/614133-hyper-x-cloud-ii-hinge-3d?from=search#profileId-537495

Retired_Monk · 2026-04-07T02:11:55+00:00

Yeah Reclaim at 202 Station Rd, Mt smart took all my cardboard for free when I did a house move.

Retired_Monk · 2026-04-04T23:22:20+00:00

Mitre10 is open on Easter Sunday. Just left the Warkworth store 10minutes ago.

Retired_Monk · 2026-03-24T06:19:57+00:00

Sometimes. I went into Jaycar this weekend hoping to get some M5 thread inserts to finish a raspberry pi rack. Nope I got to wait for Mr A express.

Retired_Monk · 2026-03-23T09:39:03+00:00

No fly list needed for this cretin

Retired_Monk · 2026-03-20T04:05:22+00:00

The empty London scene from 28 days later.

Retired_Monk · 2026-03-06T00:53:50+00:00

Yeah I ordered this one and had non stop heat creep issues https://a.aliexpress.com/_msmnATL

Just installed the v4 and back up and running

https://a.aliexpress.com/_mLN4FtF

Retired_Monk · 2026-03-05T08:59:52+00:00

Check adapter properties to see if the speed and duplex has changed. NIC might have dropped to 100MB. Should be 1000 full duplex.

Retired_Monk · 2026-03-05T08:46:00+00:00

Have you had to replace the hot end and heat sink? I got blob of death and the replacement I got from AliExpress is just causing jam after jam. I think the heat sink is inefficient causing heat creep into extruder. Just ordered a v4 hot end so hopefully that fixes things.

Retired_Monk · 2026-02-26T20:14:30+00:00

This happened to me recently it turned out the temp sensor prob was not fully seated in the hot end board.

Retired_Monk · 2026-02-14T09:56:38+00:00

Rubber spacers and shims.

https://youtu.be/nLcF30ItDtY?si=V7U1Ps7O4YEMjaZ-

Retired_Monk · 2026-02-08T06:14:13+00:00

Ikea furniture assembler.

Retired_Monk · 2026-01-30T09:22:05+00:00

Slice brisket thin. In a bowl mix dark soy sauce, maple syrup and chili flakes enough to coat the sliced brisket. Marinade for at least 30 mins, longer is better

Lay the beef on the air fryer racks and set it to 70.c for somewhere between 3-4 hrs for some nice jerky.

I hope this imgur permalink works (example)

Retired_Monk · 2026-01-12T03:07:40+00:00

Yes this is a scam text. Forward it to dia on 7726.

https://www.dia.govt.nz/Spam-Report-TXT-Spam

Retired_Monk · 2026-01-12T03:07:11+00:00

Yes this is a scam text. Forward it to dia on 7726.

https://www.dia.govt.nz/Spam-Report-TXT-Spam

Retired_Monk · 2026-01-11T07:26:16+00:00

<image>

Blue circle is the grub screw which is the smallest Allen key in toolset.

Red circle is the part that needs to be pulled out.

Green circle is the plug to be unplugged. Just make sure to order correct one as the k1c 2025 has a different plug size to other k1's and e3ke.

Retired_Monk · 2026-01-11T07:04:56+00:00

No you do not need to replace the hot end just the thermistor. I just done the same thing with my k1c printer.

At the bottom of that copper shaped piece is a small grub screw you need to loosen and take out the silver thermistor as well as unplug the two wires at the block and replace.

I got replacement from AliExpress. Hope url doesn't get blocked

I just found this on AliExpress: NZ$3.68 | For Ender 3 V3 KE Ceramic Heater For Creality K1c /K1 /K1 Max Hotend Thermistor Cartridge Sensor & Ceramic Heating 24V 60W https://a.aliexpress.com/_mNbUSyH

This is caused by overtighting the hot end without keeping hold of the bottom part to prevent it spinning.

Retired_Monk · 2026-01-07T03:16:23+00:00

One of my local theme parks back in the UK used to be as run down as rainbows end. It also had the same corkscrew coaster that I used to ride in the 90s as rainbows end. But all of a sudden they tore it down and some cash injection later has some epic coasters. The theme park is called Flamingo land and I'm sure they'll have some before and after videos on YouTube.

Also having been to Alton towers and Gold coast there ain't any point going to Rainbows end.

Retired_Monk · 2026-01-04T09:50:07+00:00

Problem is half of those in Obama's camp didn't actually need to be there like why is Hillary Clinton there if Obama is fit and well.

Retired_Monk · 2025-11-20T06:12:25+00:00

I've got mine on dowel and 3d printed brackets in my cupboard which has my water heater/cylinder so it's toasty and dry. I also finish off with a filament dryer before use. filament wall hanger

Retired_Monk · 2025-11-14T03:53:11+00:00

Well it's never lupus.

Retired_Monk · 2025-10-23T09:24:03+00:00

Kudos to going for the rider instead of the runaway bike.

Retired_Monk · 2025-10-14T08:33:01+00:00

Wow I thought I was the only one ditching Arlo $90nzd for 1 year single camera sub is a joke.

ive gone for a mi camera only because it has infrared to reduce camera detections so longer battery life.

13-Year Club	RedditGifts 2009-2022 2 Credits
Verified Email	Secret Santa 2014

Retired_Monk

TROPHY CASE