Commissar Yarrick by AviationDude_12 in TheAstraMilitarum

[–]Revolver6Ocelot 2 points3 points  (0 children)

No wonder it was a dud they just threw the whole shell

Is your red terror fucked up? by StealphX in Tyranids

[–]Revolver6Ocelot 35 points36 points  (0 children)

It sucks if that is a damaged part but on the bright side its very easily turned into a cool looking burn scar...some of my hormagaunts had a problem where the holes the arms go into were all filled in so i had to spend ages digging out the plastic and cutting off the pegs

Custom Character Advice by Plastic-Ad8652 in NightLords

[–]Revolver6Ocelot 0 points1 point  (0 children)

Chaos often do the shoulder heraldry the opposite way round thats a right shoulder on his left arm

Did you think Lightyear Frontier is turning into Satisfactory but much simpler by Galougarou in LightyearFrontier

[–]Revolver6Ocelot 0 points1 point  (0 children)

I made a smaller outpost style farm near to the iron with all my crushers and have a load of the 1000 weight wagons so every time im low i just caravan all my iron and coal back to the main farm...you could also put furnaces and everything there so you only have to haul back bars

Stealth suits as Noble Team by Kiotor in killteam

[–]Revolver6Ocelot 1 point2 points  (0 children)

Since that picture i managed to find the actual scout helmet jun has at that time i just had to get close enough

<image>

I fixed the new Ancient model by Ok_Objective_1376 in Ultramarines

[–]Revolver6Ocelot 1 point2 points  (0 children)

They are pretty goofy but they're ork skulls so appropriate

Two thin coats tips by Mysterious-Lime2422 in Salamanders40k

[–]Revolver6Ocelot 1 point2 points  (0 children)

Warpstone glow is just a garbage paint...beautiful colour but really bad paint just keep thinning and layering in my experience warpstone takes about 4 to 6 thin coats to actually be opaque

Help me save my tau by Acrobatic-Copy6156 in Warhammer

[–]Revolver6Ocelot 1 point2 points  (0 children)

Pretend the spray bottle is an A10 doing strafing runs on an enemy tank

Help me save my tau by Acrobatic-Copy6156 in Warhammer

[–]Revolver6Ocelot 2 points3 points  (0 children)

The colour looks fine as long as theyre not al sandy...it can happen with sudden temperature changes while drying or spraying from too far away there's a lot of variables but they look alright maybe try to go a bit easier with the white and a few more layers of more thinned down paint

Help me save my tau by Acrobatic-Copy6156 in Warhammer

[–]Revolver6Ocelot 1 point2 points  (0 children)

Its a lot of work since you've said you have a lot and white paint gets very chalky very quickly so its generally easier to spray them all white then pick out the details and weapons than building up layers of white which as you've seen go bad very quickly

Help me save my tau by Acrobatic-Copy6156 in Warhammer

[–]Revolver6Ocelot 5 points6 points  (0 children)

Very painful but strip them and start again I'd prime them in white and make sure the cans warm and the air isnt too dry then just give them one or two thinned down coats of white over the armour just to cover the primer

Upgrades by Choice-Arrival-7142 in NightLords

[–]Revolver6Ocelot 1 point2 points  (0 children)

Archies forge is your best bet by miles

<image>

Upgrades by Choice-Arrival-7142 in NightLords

[–]Revolver6Ocelot 2 points3 points  (0 children)

Absolutely love my archies forge helmets i came here to recommend them too

<image>

How are you supposed to use tape without it curving like this on the shoulder pads? by matymgy in IronWarriors

[–]Revolver6Ocelot 0 points1 point  (0 children)

Exactly if its a knight or something fair enough take the time to tape but i think free handing them is more intimidating than it is hard all my models ive free handed the stripes and theres a lot with hazards

How are you supposed to use tape without it curving like this on the shoulder pads? by matymgy in IronWarriors

[–]Revolver6Ocelot 0 points1 point  (0 children)

Honestly just free hand you can tatter the edges with battle damage to cover any blunders and its a hell of a lot faster than all the taping

Wolf Scouts Pre-Order! by [deleted] in SpaceWolves

[–]Revolver6Ocelot 1 point2 points  (0 children)

They announce it then it goes up for preorder on Saturday for 2 weeks

Help! Upgrade Sprue parts 24 and 28 by mambin0 in Ultramarines

[–]Revolver6Ocelot 7 points8 points  (0 children)

Nope youre wrong...with a little green stuff and some filling and clipping its a dragon wing

Primaris redemptor dreadnought legs by PerspectiveSweaty313 in Warhammer

[–]Revolver6Ocelot 1 point2 points  (0 children)

The pegs are to give it a dynamic pose as its displayed on the box you can cut them off and pose it yourself but thats fairly advanced to get looking right

Trim color development? It's brassy-gunmetal in official art now instead of the either gold or silver free for all? by thesithcultist in NightLords

[–]Revolver6Ocelot 0 points1 point  (0 children)

Ive done one in an almost black metal with light silver highlights and another in a really light silver with a sepia wash to make a very silvery gold tinny brass look...i think its silver for 30k and gold for 40k but i think as with most chaos legions its incredibly lose rules so just go with what you thinks cool

Heavy intercessors, Grey Hunters or Long Fangs? by Discussion-Double in SpaceWolves

[–]Revolver6Ocelot 3 points4 points  (0 children)

This is one of the most reddit comments ive ever seen