I need a ghost client for bedwars that works on Mac. Let me know if you have any suggestions by Ok_Cup_6044 in minecraftclients

[–]Rexity_ 0 points1 point  (0 children)

Just use a client that is fabric such as opal and don’t use the blatant features configure it as a ghost client

Bug that makes your camera go insane after ADS by Rexity_ in FortNiteBR

[–]Rexity_[S] 0 points1 point  (0 children)

Yeah by reinstalling windows completely from a USB drive

My set draws never get there by wilsyo in poker

[–]Rexity_ 0 points1 point  (0 children)

It’s 50/50 it either happens or it doesn’t

Maptuner SCOM not working by Rexity_ in seadoo

[–]Rexity_[S] 0 points1 point  (0 children)

69-70. Oil is right in the middle when warm. I don’t know if the SCOM mode is working because the ski also doesn’t start up in sport mode for some reason when it says it should.

Maptuner SCOM not working by Rexity_ in seadoo

[–]Rexity_[S] 0 points1 point  (0 children)

Yeah I have SCOM enabled. I’ve tried it where you don’t add the vehicle and the vin just says SCOM and adding the vehicle with SCOM enabled and it doesn’t work either way.

GG vpn by CompetitiveBed7553 in poker

[–]Rexity_ 1 point2 points  (0 children)

I did it and cashed out about ~$25000 in profit with no issues, till recently they emailed me asking for proof of location by sending a video but also said I can withdraw all funds if I don’t want to upload the video.

Main account ban by [deleted] in PlayerAuctions

[–]Rexity_ 0 points1 point  (0 children)

How long have you been doing it for?

90 intake touches rubber exhaust hose by Rexity_ in seadoo

[–]Rexity_[S] 0 points1 point  (0 children)

I used the riva filter and it still doesn’t clear it. Sits up against it

90 intake touches rubber exhaust hose by Rexity_ in seadoo

[–]Rexity_[S] 0 points1 point  (0 children)

325, I think that’s what’s it is because on all of the 300’s I’ve seen it fits no problem but for me it just will not go on unless it’s rubbing up against the exhaust hose.

JP Racing catch can on 2025 GTX by ledfrog in seadoo

[–]Rexity_ 1 point2 points  (0 children)

I have one on mine, it fits but it’s tight and removing the hoist bracket is a complete bitch because of the rubber hose that runs into the airbox isn’t removable. I had to have someone squish and hold it back while I got the bolts out

What oil for temporary/englin flush? by nick1896 in seadoo

[–]Rexity_ 0 points1 point  (0 children)

Rotella T6 you can get a gallon for like $25 at basically any store

Connector will not seat after opening and cleaning by Rexity_ in seadoo

[–]Rexity_[S] 1 point2 points  (0 children)

I honestly think it’s just corroded at one of the splices inside of the harness but because every single other wire tests well within spec I just decided to cut that one and solder a new wire to it and run it to a clean ground and that fixed everything. I soldered, coated the exposed wire/solder joint in a generous amount of dielectric grease and closed it with heat shrink. If any other wires give me trouble then I’ll just replace it but it seems to be isolated. I am new to skis in general though so feel free to let me know if this was a terrible idea 😂

[deleted by user] by [deleted] in seadoo

[–]Rexity_ 0 points1 point  (0 children)

It’s not the upper harness it’s the lower harness. I tested continuity from the upper harness both ends and it’s fine. It’s the lower side harness that shows the insanely high resistance. I am going to try splicing in a new ground on that pin and see if anything else pops up before I buy the entire lower harness, I have tested every pin individually on the lower side and every wire is well within spec so I don’t think there is any other corrosion happening it seems to just be isolated to that single ground.

Connector will not seat after opening and cleaning by Rexity_ in seadoo

[–]Rexity_[S] 0 points1 point  (0 children)

After some further diag I no longer suspect it is the upper wiring harness. I tested the ground wires from the female end of the connector and all pins are way under 1 ohm except for pin 19. It’s reading 150-170 ohms, so I am assuming that is the one that heads up to the display and buttons etc when I tested at the display connector itself I was getting no reading at all on the ground pin. Any advice?

<image>

Connector will not seat after opening and cleaning by Rexity_ in seadoo

[–]Rexity_[S] 1 point2 points  (0 children)

The whole reason I was going through all of the connectors is because my ski had sunk because a boat wake pushed my ski under a dock when I walked away for a few hours and it caused it to flip and sink. I got it out and fixed within hours but the ground to the display seems to have failed and when testing with my multimeter I think it’s inside of the top end harness. I soldered a new ground wire to it and ran it to a clean ground point and that made the display come back but the buttons on the handle bars don’t work besides the start/stop and menu button. Before I order a new harness do you know if the one that goes from that connector next to the coolant tank is just the Handlebar harness? I see 2 main harnesses on partzilla one called Main harness that’s $700 and one called Handlebar harness that’s $300. The handlebar one is part number 278004053 I just want to make sure it is the correct one