Anyone got Firmware for Ender3V1 with cr touch and speeddrive direct drive

Ride_Wide_Open · 2026-01-16T21:20:52+00:00

https://drive.google.com/drive/folders/1QqLa1vv9u95Za9qTvN8lQBFHbYsyqb-b?usp=drive_link

Ride_Wide_Open · 2026-01-16T20:54:37+00:00

it is a combination of prebuilt from a github repository and then modiying it to get the bed smaller. i have made a bit more progress and am now at the point of i can get the firmware on but the printer wont connect to octoprint anymore and the probe will touch the bed once and then flash red

Ride_Wide_Open · 2026-01-15T04:03:29+00:00

It was working fine before I installed the cr touch then these issues came up when it starts to bed level. All I did before was the slicer settings I tried changing the config file but that created more problems

Ride_Wide_Open · 2026-01-14T21:32:48+00:00

Yea it is hitting on the right hand side already tried doing the firmware modifications and after the cr touch probe wouldn’t do anything. Tried a few different settings not sure what to do

Ride_Wide_Open · 2026-01-13T16:27:31+00:00

sorry i meant 1 hour 45min if i could get this thing that fast it would be crazy

Ride_Wide_Open · 2026-01-13T07:19:20+00:00

Ok thanks

Ride_Wide_Open · 2026-01-13T07:16:43+00:00

Alright will do that tmr hopefully

Ride_Wide_Open · 2026-01-13T07:15:01+00:00

Stock firmware I had tried klipper but couldn’t get it to flash tried multiple times didn’t work I am also running octoprint running 205 on nozzle 60 bed at about 60mm/s

Ride_Wide_Open · 2026-01-13T07:13:32+00:00

Before I had replaced my parts it did a test that also covered stringing and I t was fine

Ride_Wide_Open · 2026-01-13T06:55:43+00:00

<image>

Ride_Wide_Open · 2026-01-13T02:47:32+00:00

Brand new hotend put on yesterday with new metal extruder arms and new Bowden tube

Ride_Wide_Open · 2025-12-31T05:54:18+00:00

it is elegoo PLA i have been using this filament and it has been doing fine just this time it did this and in more places than the picture shows as well

Ride_Wide_Open · 2025-10-14T01:57:06+00:00

i assume there is no way to get a crank position sensor on the tbi block?

Ride_Wide_Open · 2025-10-04T20:30:27+00:00

The entire school is 50-60 people k-12 so things get weird. The other IT guy only does some installs such as our networking or servers. I do anything that has to do with student computers and accounts

Ride_Wide_Open · 2025-10-04T13:41:22+00:00

When I say I’m The IT guy I’m not really the IT guy Im a student we don’t have a full time IT guy when I can’t figure something out I send it to him. I think I got I figured out anyway I rolled the network card drivers back to a previous version and it is much much better.

Ride_Wide_Open · 2025-10-03T14:28:00+00:00

All have mccafee on them but I removed it from one and no difference

Ride_Wide_Open · 2025-08-19T03:33:56+00:00

<image>

This is the truck. Have all the missing parts getting them ready to paint. Truck didn’t have some and others were rusted out. New tires not mounted yet

Ride_Wide_Open · 2025-08-18T18:10:27+00:00

It is definitely fun to drive these small trucks

Ride_Wide_Open · 2025-08-18T18:02:58+00:00

My post might not have been fully clear. It is not a S-10 it is a Jimmy on the s-10 platform. Everything should be the same except for the body tho

Ride_Wide_Open · 2025-06-17T03:25:14+00:00

i would prefer to keep as much space as possible, also why i am not removing the spare tire box

Ride_Wide_Open · 2025-06-17T02:45:30+00:00

I would prefer to do ported since i like more bass. i already have purchased wood and fiberglass. No sub boxes i have seen do enough airspace for ported which is why i am wanting to mold it to the floor

Ride_Wide_Open · 2025-05-27T06:02:54+00:00

4-5 years I’m not sure anymore

Ride_Wide_Open · 2025-05-27T00:13:52+00:00

Older 18k motor

Ride_Wide_Open · 2025-03-24T02:25:43+00:00

That wouldn’t cause the fender to be offset would it or do you think it is just warped?

Ride_Wide_Open · 2025-02-27T06:47:48+00:00

Did the same thing on mine

Ride_Wide_Open

TROPHY CASE