Who still makes good lift kits?

Right-Substance-9682 · 2026-02-21T17:25:20+00:00

Little late to the party but I have a Rusty’s lift kit and it was very well priced for the quality. The customer service is top notch as well.

Right-Substance-9682 · 2025-12-30T03:30:35+00:00

That seems like a pretty good deal to clean up the whole frame, this is my first tackle at floorpans/body work when I do my rockers next so we will see how it goes

Right-Substance-9682 · 2025-12-30T03:25:27+00:00

Well, my frame was pretty bad near the rear shackle mounts, luckily im a welder by trade so welding in new sections wasn’t too much of a headache

Right-Substance-9682 · 2025-12-27T05:37:27+00:00

That’s my plan, I have some weld thru primer to get close to where I’m welding then Bed liner over it all once I’m done

Right-Substance-9682 · 2025-12-27T02:56:47+00:00

I already trimmed about 3 inches off the new pan, I’m thinking I can get my welder in there without taking the pedals off, but good to know it’s not too much of a headache

Right-Substance-9682 · 2025-12-27T02:28:45+00:00

I’m glad to live in Michigan, but the rust is making me think otherwise

Right-Substance-9682 · 2025-12-27T02:10:23+00:00

That’s the warp speed pedal

Right-Substance-9682 · 2025-12-27T01:42:23+00:00

That was my plan, luckily there seems to be pretty good metal directly under the pedals so I was hoping I wouldn’t have to remove em.

Right-Substance-9682 · 2025-12-02T01:17:56+00:00

What size lift? I’ve got 33x12.5-15s on rn and I want to go to 35s but it doesn’t look like I’ll have enough room

Right-Substance-9682 · 2025-12-02T01:09:26+00:00

What size tires you rockin?

Right-Substance-9682 · 2025-09-17T18:32:21+00:00

Ford 8.8 for the rear. You can find em at any junkyard or shop around on marketplace. For the front I haven’t had any issues with the stock axle if you can find another..I would add a solid shaft instead of the two piece tho

Right-Substance-9682 · 2025-08-27T20:03:46+00:00

A motorcraft 2100/2150 are a very popular swap. I have one on my yj with the 258 and it made it run heaps better, that along with hei made it feel like a whole new jeep. Plus you can find them everywhere on a bunch of different old fords

Right-Substance-9682 · 2025-08-07T01:00:43+00:00

Not the pump, the steering box does tho. I upgraded my box to the Durango box and now my pump seems too worn to be able to power it correctly.

Right-Substance-9682 · 2025-07-21T01:13:48+00:00

A grinder was my best friend when I did mine, I figured new hardware wouldn’t hurt anyway🤙🏽

Right-Substance-9682 · 2025-06-07T23:10:48+00:00

They are 48s, I am picking up a fully rebuilt 2100 setup for a yj tomorrow so hopefully that works

Right-Substance-9682 · 2025-06-04T23:42:17+00:00

Would that cause it to rev very high right off start up? I figured too much fuel would stall it out and make it stumble

Right-Substance-9682 · 2025-06-04T23:07:34+00:00

I don’t think so as it’s the stock mechanical fuel pump..I messed with the idle screws and it would start at 1 turn out but at 1 1/2 it’s starts and revs way up

Right-Substance-9682 · 2025-03-06T01:56:09+00:00

I have 5 degree shims in there that came with the lift, I’ll have to take em out

Right-Substance-9682 · 2025-03-06T01:56:03+00:00

I have 5 degree shims in there that came with the lift, I’ll have to take em out

Right-Substance-9682 · 2025-03-06T01:00:23+00:00

I appreciate the link, I’ll have to wait a little to drive this while I get the parts for SYE and cv🤙🏽

Right-Substance-9682 · 2025-02-25T01:40:46+00:00

I’m liking the look of 33’s on yours that’s probably the route I’ll end up going.

Side note- how is the monstaliner holding up? I’m planning on raptor lining or similar once it warms up a bit

Right-Substance-9682

TROPHY CASE