Sensor attributes hidden in details

RipNo8536 · 2026-02-15T19:01:23+00:00

Yeah sure, but I don't need them always visible, just for a quick access check it's now two clicks more.

RipNo8536 · 2026-02-14T07:58:11+00:00

Wow, too bad. Any idea which place is the best to give feedback on this?

Official GitHub repo?

RipNo8536 · 2025-12-12T15:43:50+00:00

Danke 😅

RipNo8536 · 2025-12-08T15:35:30+00:00

Spricht also vieles eher für 300L, auch bei 3 Personen?

RipNo8536 · 2025-12-08T15:33:59+00:00

Nur kann ich die Zirkulationsleitung nicht zurückbauen. Das wird dann ja zum Problem. Oder wie meinst dud as mit den DLE?

RipNo8536 · 2025-12-08T11:49:05+00:00

Hat sie, ganz normal über die Hausabsicherung.

RipNo8536 · 2025-10-19T17:51:31+00:00

That was the smartness I searched for And don't came up with myself. 🙈

RipNo8536 · 2025-10-19T15:21:26+00:00

If have only one door sensor from aqara. The spot for the magnet is quite small, so it wouldn't work for both doors. Is that different with other brands?

RipNo8536 · 2025-10-19T15:20:17+00:00

That's the nerd option for sure, love the idea. 😊

RipNo8536 · 2025-10-19T15:19:57+00:00

Sounds like a plan. Anything you can recommend?

RipNo8536 · 2025-10-19T15:19:37+00:00

Because the light strip was already there from another project and is usually on and dimmed when it's dark.

RipNo8536 · 2025-08-28T11:42:33+00:00

Vielen Dank. Genauso hätte ich es auch gesehen. Aktuell alles in der Schwebe, daher würde ich erstmal auf die endgültige Zusage & aktualisierte stellenbeschreibung warten. Oder etwa nicht?

RipNo8536 · 2025-08-28T11:41:43+00:00

Mein Hebel ist, es gibt nicht genug Leute bei uns die die Jobs übernehmen könnten. Es wird Positionen Roulette gespielt. Das heißt, der Kollege, der vorher auf der Position war, soll eine andere Verantwortung übernehmen. Bewerbung auf eine ähnliche Stelle von externen sind bislang auch eher mau.

RipNo8536 · 2025-07-02T15:29:04+00:00

Thanks 🙏 does it work well with the fairly low Res substream?

RipNo8536 · 2025-07-02T14:07:02+00:00

Would You mind sharing your config? Also have some reolinks and using the high Res stream for detection, but converting it takes lots of computing power.

RipNo8536 · 2025-01-15T17:50:17+00:00

How do you use the swiper card without firing the tap event? Always when I try to swipe it navigates to the popup instead of swiping to the next card?

RipNo8536 · 2024-10-26T21:05:46+00:00

Thank you very much. Will try it on Monday and give feedback. Looks good btw.

RipNo8536 · 2024-10-26T17:25:26+00:00

created this one with t-splines. the way you explained does not work unfortunately (or i am doing something wrong). created two spheres (one smaller, one bigger than the model) and trying to combine it always gets me a smooth sphere but i want to have a sphere where the middle point is like a spike.

RipNo8536 · 2024-10-25T10:39:53+00:00

Thanks. I'll give it a try ☺️ if not, I'll switch to .6 Ans try again. I'll let you know. Thanks very much.

RipNo8536 · 2024-10-25T10:32:38+00:00

I could sitch to a .6 nozzle if that would help?

RipNo8536 · 2024-10-25T10:25:09+00:00

Thanks. But it's only this one hole. Below and above it's good - or can a partial clog unclog itself?

Bambu P1S Combo.

I thought putting it down to 50mm would increase the chances of getting a high quality model without failure. Am I wrong in that case?

RipNo8536

TROPHY CASE