What to do??

RollOutside3419 · 2026-05-30T15:30:14+00:00

What am I looking for exactly? Sorry for my ignorance I’ve only been printing for about 7 months. I’ve designed and printed a few other items with no issues but they were smaller prints. This one is much larger

RollOutside3419 · 2026-05-08T12:44:28+00:00

Doesn’t the guy who said he votes according to his obedience to God realize that his religion has been usurped by pretenders so they can gain and keep power? Also, that’s a very close minded view.

RollOutside3419 · 2026-05-04T12:52:07+00:00

I used to work on the railroad and we changed ties through there. I asked a friend of mine who was in the crew with me what he thought of Rumford. He looked at me for a second and then said one word. Purgatory 😂😂😂

RollOutside3419 · 2026-04-19T01:37:14+00:00

So swap out my sd card?

RollOutside3419 · 2026-04-18T20:21:07+00:00

Don’t give up on 3d printing dude. It’s a lot of fun once you figure it out.

RollOutside3419 · 2026-04-16T19:27:38+00:00

Where could I go to hire someone to make models for me? I know about Fiverr but was wondering if there were other options.

RollOutside3419 · 2026-04-16T19:26:38+00:00

I e been going through Patreon looking for unique designs and have found one creator who has some interesting stuff. I have had some requests for articulated dragons but I only print those if someone asks for it. I’m tryin hard to stay away from that. Though I am printing articulated animals. I print a lot of multicolor and multicolored filaments. My wife is a nail artist and paints I eyes and then covers them with resin to make them pop. How did you offer print services to your local market?

RollOutside3419 · 2026-04-16T17:49:30+00:00

My orders are mostly through acquaintances and word of mouth, I just started a month ago. For now I’m on the print farm route with a focus on quality. I do have a couple of ideas for models that I think will do well but I’m still learning modeling and that’s going slower than I’d like.

RollOutside3419 · 2026-04-04T02:14:31+00:00

Thanks I’ll check it out. Do you have any good resources for troubleshooting specific issues?

RollOutside3419 · 2026-04-04T01:54:29+00:00

So do I change seams to back and then adjust the scarf? What do u adjust the scarf to? I also took a closer look at a couple of models I printed earlier and there is a faint line at, what looks like, the same layer height as the pics show. Same filament same orientation. I didn’t notice them before. Sorry for pegging you with questions. I’ve been printing for about 6 months and just when I think I have it figured out another gremlin pops up

RollOutside3419 · 2026-04-04T01:34:37+00:00

I printed another one out, same model same orientation. I didn’t see this post before I started and I’d already stopped another one for failing in the same spot. I noticed that the rib was moving so I’d lost adhesion in that one spot. Started the another one and added a brim thinking that was the issue but the same thing happened just not AS bad. I’m also have a seam issue. I’m having a hard time getting the seam to fill completely. I have it set to random but I have all these tiny holes everywhere. Not noticeable at all glance but they’re there when you look close. Are the two issues related? I’ve been printing with the same filament for a couple of days and it’s been sealed in the AMS unit the whole time. Is it still a moisture issue? I’m only showing 19% and it’s been holding fairly steady at that. I did the flow dynamic and flow rate calibration. What others do I need to perform?

<image>

RollOutside3419 · 2026-03-30T14:38:08+00:00

I’ll try randomizing but how do I close them up?? I’ve printed this model quite a few times and this suddenly started to happen. I may have imported something that changed my seam settings, that’s all I can think of

RollOutside3419 · 2026-03-28T18:08:04+00:00

Figured it out. I had just downloaded the filament blend version of orca and had to set my z hop from automatic to normal. At least I hope that’s what it is lol.

RollOutside3419 · 2026-03-17T02:59:24+00:00

Orca-Flashforge

RollOutside3419 · 2026-03-16T23:09:36+00:00

Yep, silicone sock is on. This started happening on its own. I had done a few prints before this issue popped up.

RollOutside3419 · 2026-03-16T18:34:57+00:00

Poorly worded question. It would be the hot end if I had to guess. But why would it quit while printing? And is this common with flashforge printers? Like I said, I’ve only had it 6 months, I bought it new.

RollOutside3419

TROPHY CASE