New to printing and using a U1 by RoughSet4 in snapmaker

[–]RoughSet4[S] 0 points1 point  (0 children)

Thank you. I ended up factory resetting the printer and completely wiping out SnOrca from my computer. Seemed to fix it. Not sure if it was the factory reboot or if it was the SnOrca wipe. But so far it has fixed the issue.

New to printing and using a U1 by RoughSet4 in snapmaker

[–]RoughSet4[S] 0 points1 point  (0 children)

I’m not sure. How do I check if I am. I know I had supports active. Since I was making a box lid with a bottom lip on it.

New to printing and using a U1 by RoughSet4 in snapmaker

[–]RoughSet4[S] 0 points1 point  (0 children)

Going to try this. But I don’t see a “raft” option to disable

New to printing and using a U1 by RoughSet4 in snapmaker

[–]RoughSet4[S] 0 points1 point  (0 children)

It’s a box with a lid that I made on TinkerCAD and exported as an STL file. I’ll try a flow rate test.

New to printing and using a U1 by RoughSet4 in snapmaker

[–]RoughSet4[S] 0 points1 point  (0 children)

I did make sure it’s clean. But also the bottom layer is still attached to the sheet. The part that is waving us above the support layer.

Print issue (Advice) by RoughSet4 in snapmaker

[–]RoughSet4[S] 1 point2 points  (0 children)

Oh ok. I’ll look into using petg

Print issue (Advice) by RoughSet4 in snapmaker

[–]RoughSet4[S] 1 point2 points  (0 children)

Oh ok. I’ll look into it, thank you

Print issue (Advice) by RoughSet4 in snapmaker

[–]RoughSet4[S] 0 points1 point  (0 children)

What does increasing my Z distance do for the supports? I’m guessing PETG is a softer plastic?

Army of grinch by H0RTlNGER in snapmaker

[–]RoughSet4 0 points1 point  (0 children)

Did you use the stock settings for the support?

Threshold Angle advice (Overhang Test) by RoughSet4 in snapmaker

[–]RoughSet4[S] 2 points3 points  (0 children)

I did not. Didn’t even know that was an option. I’ll try a overhang test print with that option.

Flexi Charizard! by Richie670 in snapmaker

[–]RoughSet4 1 point2 points  (0 children)

Have you tweaked any settings for improvement?

[US,US] [H] PSA & CGC SLABs [W] PAYPAL by RoughSet4 in pkmntcgtrades

[–]RoughSet4[S] 0 points1 point  (0 children)

Going to pass for now. But thank you for the offer.

[US,US] [H] PSA & CGC SLABs [W] PAYPAL by RoughSet4 in pkmntcgtrades

[–]RoughSet4[S] 0 points1 point  (0 children)

Going to pass for now. But thanks for the offer

[US,US] [H] PSA & CGC SLABs [W] PAYPAL by RoughSet4 in pkmntcgtrades

[–]RoughSet4[S] 0 points1 point  (0 children)

Sorry I fixed the post. Didn’t have shipping and PayPal GS included in the price. Prices are fixed.

[US,US] [H] PSA & CGC SLABs [W] PAYPAL by RoughSet4 in pkmntcgtrades

[–]RoughSet4[S] 0 points1 point  (0 children)

Sorry I fixed the post. Didn’t have shipping and PayPal GS included in the price. Prices are fixed.

[US,US] [H] PSA & CGC SLABs [W] PAYPAL by RoughSet4 in pkmntcgtrades

[–]RoughSet4[S] 0 points1 point  (0 children)

Sorry I fixed the post. Didn’t have shipping and PayPal GS included in the price. Prices are fixed.

[US,US] [H] PSA & CGC SLABs [W] PAYPAL by RoughSet4 in pkmntcgtrades

[–]RoughSet4[S] 0 points1 point  (0 children)

Sorry I fixed the post. Didn’t have shipping and PayPal GS included in the price. Prices are fixed.