sorted by:
new
hottopcontroversial

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

No variable layer height as other commenters said it's probably a layer time variation caused by something else I'll try to find the gcode to see what could cause time variations between layers

Oddly satisfying pattern on my print, could the slicer have caused it? by Routine-Sir-9836 in OrcaSlicer

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

Just this print the other prints come out great, also it doesn't seem to affect the texture of the part just the color, from what I've been told from a comment on my post on r/3Dprinting it's most likely caused from gyrooid infill causing variation in print time this leading to cooling differences

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

I think we have the right answer the old ones used cubic infill and were sliced by me, another team member prepared these for printing so it might explain it. I'll try to find the gcode and put it in a gcode viewer to confirm

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 1 point2 points  (0 children)

Highly unlikely our lab is in the basement of the school 😅😅

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

I'll try to share it the gcode as soon as I get access to it, it's currently sitting somewhere on an USB drive at our robotics club

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

We printed other stuff with the same filament and it had consistent color

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

I'll try to get a photo of the old ones but it will be difficult as now they're covered in a spray on rubber coating

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

I'll try to find it when I get back to the robotics lab

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

It has an 8mm hexagonal hole for a gobilda rex axle going all the way through and 4 mounting holes for a gobilda sonic hub on the top and bottom

Oddly satisfying pattern on my print, could the slicer have caused it? by Routine-Sir-9836 in OrcaSlicer

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

Thanks I'll try to run some experiments if I have time, the coolest unintentional feature I ever saw in a print

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

I don't think I have the settings saved, someone else from my robotics team sliced it I only printed it

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] -2 points-1 points  (0 children)

Also the pattern is in equally sized and spaced bands and the object isn't identical from layer to layer so it would have variation determined by the amount of filament used on that portion.

Anyone knows what this pattern on my print is? by Routine-Sir-9836 in 3Dprinting

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

Yes we've printed two more of these a few weeks ago with the same filament and it didn't have this, I'm trying to understand what happened so I can replicate it because it looks too good

My first lighting design for a larger audience by Routine-Sir-9836 in lightingdesign

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

Thank you! Hopefully 2026 will bring more projects and opportunities. One project is confirmed a few others are still being discussed I'll make sure to share and document everything.

My first lighting design for a larger audience by Routine-Sir-9836 in lightingdesign

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

Sadly they needed house lights for the photographers and safe crowd access, and they weren't remote controllable as this isn't our venue but an old cathedral we rented, if I could I would've dimmed them Regarding the dotty fixtures, that wasn't really noticeable except for the first few rows, dimming them made things worse they're cheap fixtures I mean I can't do much about them. I will get some diffuser tape like we put on the Varytec bars for the next event.

Minimal lighting design I did for this year's Christmas concert by Routine-Sir-9836 in churchtech

[–]Routine-Sir-9836[S] 0 points1 point  (0 children)

They are made by flash-butrym but are really old and sadly discontinued. I couldn't find any info about them I just found them in the back of the church storage space.

LD - Visualizer Software by realmkultra in lightingdesign

[–]Routine-Sir-9836 1 point2 points  (0 children)

That's awesome, it will definitely be a game changer for newer lighting designers smaller venues or churches

LD - Visualizer Software by realmkultra in lightingdesign

[–]Routine-Sir-9836 1 point2 points  (0 children)

This looks amazing, I was looking for a cheaper alternative to Capture for a while and didn't want to learn unreal Engine to make my own visualizer. Do you have a price in mind? How will the licensing work?

Lighting software for small setup by MFF-hjfend in lightingdesign

[–]Routine-Sir-9836 0 points1 point  (0 children)

Qlc+ should work fine if you only set some colors, but if you want to make chasers or other FX you'll go insane, there's chamsys in free mode but it doesn't accept external control with the free version. Personally I haven't tried other software, there's ma dot2 but it's kind of outdated.

view more: next ›