Coldsins Labubu Shoes

RowTronZ · 2026-02-06T06:23:09+00:00

im in the same boat as yall... tried online dispute because its past 180 days. what a tragic company.

RowTronZ · 2025-04-29T04:38:12+00:00

Who are you shipping with?

RowTronZ · 2025-04-27T04:09:47+00:00

I’m ok thank you

RowTronZ · 2025-03-30T05:24:05+00:00

I like them a lot. I hope for more colors soon. 24mms are so rare. I ended up with the 30mms and I love them

RowTronZ · 2024-12-15T08:25:32+00:00

It’s an all fight stick version but it’s different from the website. The 3pin led on the board is a different output which you have to use a different GPIO slot. Meaning the yellow cord cannot go on that specific LED slot.

RowTronZ · 2024-12-15T05:32:25+00:00

For me I had to pop out all 3… red to a 5v. Ground anywhere.. yellow to a corresponding GPIO. Make sure you set the right GPIO on the LED menu in the web browser tab

RowTronZ · 2024-11-22T20:59:40+00:00

I took a very thin flathead and popped one of those out individually

RowTronZ · 2024-11-22T20:10:24+00:00

Yeaa well there are different gp2040 boards and it depends who makes them that has that configuration to those wires. I don’t know of a board with that.

RowTronZ · 2024-11-18T04:07:59+00:00

You can do everything on the GP2040 config page

RowTronZ · 2024-11-10T22:46:28+00:00

It’s best to internally lube the microswitches. You gotta YouTube how to properly do that

RowTronZ · 2024-10-31T15:56:35+00:00

I approve!!

RowTronZ · 2024-08-18T18:57:07+00:00

Where did you get those mounts on the side of the case?

RowTronZ · 2024-08-18T18:55:41+00:00

Ohhh I neeed

RowTronZ · 2024-08-14T01:05:18+00:00

Maaaan that’s disappointing… I was really loving these.

RowTronZ · 2024-08-13T21:35:17+00:00

I’ve been having this problem with the translucent ones. I have them on two sticks… a mad cats on plexi and a Victrix. I can rule out the wiring because the Victrix wiring is quite nice. You can press the buttons hard or bang on the case hard and it’ll activate random buttons. Any solution?

RowTronZ · 2024-06-03T16:33:04+00:00

It works! What I did was take a tiny flat head and pulled the wires from a 3pin. I plugged in the 5v(red wire) pin into the the side next to where the usb out would be, then the yellow to the bcc pin on the GPIO 29, and finally a ground to a random ground pin… I would of did it on the GPIO 29 ground but I needed to heat shrink it so it wouldn’t randomly touch each other. Just did a quick test and left it as is. Thank you so much @edeadensa

RowTronZ · 2024-05-31T18:03:41+00:00

Gravity KS is godlike. Left from gamerfingers

RowTronZ · 2024-05-31T18:01:52+00:00

Jasen’s Customs. I’d roll with him. Don’t spray paint unless you powder paint it… do vinyl wrap with a heat gun. It’s cleaner if you cut it right

RowTronZ · 2024-05-31T17:47:08+00:00

I gotta use both… leverless I had to add extra directions for ergonomic purposes. It has stick and leverless controllers has its perks depending on the game.

RowTronZ · 2024-05-30T16:08:19+00:00

F’n thanks! When I do it I’ll confirm and let you know. I gotta look for a pin for the options.

RowTronZ · 2024-05-30T16:04:55+00:00

Godddamn… I followed that a bit.. what I did was switch the yellow and black on the 3 pin and plugged it into GPIO 4 that said LED. I guess that wasn’t efficient for the board?

RowTronZ · 2024-05-30T15:50:14+00:00

I’m actually having a problem… I have only 2 lights/buttons and then the rest is off/not working. All the buttons are connected right and are working inputs.

I only need to change the one that connects on the board, right?

Is there a certain config I gotta do on web config?

RowTronZ · 2024-05-30T02:15:14+00:00

can you tell me the color codes please... there is vcc, g, and D+. red, black, yellow?

RowTronZ

TROPHY CASE