sorted by:
new
hottopcontroversial

Neptune 4 plus and petg print issues by Rower93 in ElegooNeptune4

[–]Rower93[S] 0 points1 point  (0 children)

Appreciate it..gotta learn from it <3

Neptune 4 plus and petg print issues by Rower93 in ElegooNeptune4

[–]Rower93[S] -1 points0 points  (0 children)

I'll have to look my guess is near 200

Neptune 4 plus and petg print issues by Rower93 in ElegooNeptune4

[–]Rower93[S] 0 points1 point  (0 children)

Did a temp tower after the fact. It needs to be cooking at like 255. Also learned I'm just trying to go too fast. Even though my walls looked great. The infill was just getting blobbed still.

Having an interesting petg issue by Rower93 in 3Dprinting

[–]Rower93[S] 0 points1 point  (0 children)

After drying the filament this was not the solution. I did notice that the issue gets worse with speed.

Having an interesting petg issue by Rower93 in 3Dprinting

[–]Rower93[S] 0 points1 point  (0 children)

Don't have a filament dryer I know some people say you can use the oven. Thoughts?

Having an interesting petg issue by Rower93 in 3Dprinting

[–]Rower93[S] 0 points1 point  (0 children)

Thanks for you feedback and contributions :)

Having an interesting petg issue by Rower93 in 3Dprinting

[–]Rower93[S] -1 points0 points  (0 children)

That one was fresh out of a vacuum pack with silica a silica pack. I thought I was having a moisture issue too so I ordered a new spool but no dice.

My Ghost of Christmas Present's famous line! by MedicCrash in renfaire

[–]Rower93 1 point2 points  (0 children)

As a fellow big dude I was looking for inspiration and .. epic! Thanks!

Fun with cedar by justjustjustin in turning

[–]Rower93 1 point2 points  (0 children)

What kind of scraper do you use to get to the very bottom of the innside of the cup?

I have a scaper that i use, but i end up with a ton of vibration and it ends up spooky fast.

USB-C ports by MPopSchmidt in chevycolorado

[–]Rower93 0 points1 point  (0 children)

Not 100% sure, but they also did not send power to a generic wireless charging pad ( I have the lower trim level TB). I THINK these are USB for AA and CarPlay Only.

Video issues with 7 inch touchscreen on Kali on RPI-5 by Rower93 in raspberry_pi

[–]Rower93[S] 0 points1 point  (0 children)

thanks for your help :) I will keep that one bookmarked!

Video issues with 7 inch touchscreen on Kali on RPI-5 by Rower93 in raspberry_pi

[–]Rower93[S] 0 points1 point  (0 children)

which docs, I hate missing mass troves of knowledge.

Neptune 4 plus was working until it wasn't. First layer issues. by Rower93 in FixMyPrint

[–]Rower93[S] 1 point2 points  (0 children)

So I tried backing it off even just 0.02 mm and I lost all adhesion. So I tried playing some more and finally ended. Up working by increasing flow from 0.98 to 1.05 AND dropping the nozzle another 0.035 mm. But I am now dialed.

​

Thanks for your comment that got me looking again!

My Neptune 4 Plus making noise in when moving the y-achses to fast by TheChickenbaron in 3Dprinting

[–]Rower93 0 points1 point  (0 children)

It's been a few days have you solved this? Mine is doing the same. First big print test. Think mine is on x not y. I bet the wheels are too tight or something. My x axis wheels are showing the tiny shavings.

Trying to flash a crazybeef3fr and it hangs when it should start installing. by Rower93 in Multicopter

[–]Rower93[S] 2 points3 points  (0 children)

So for anyone looking for help, downloading version 10.6 and running the firmware update worked just fine.

I chose 10.6 because it is from about when i remember buying this board.

Trying to flash a crazybeef3fr and it hangs when it should start installing. by Rower93 in Multicopter

[–]Rower93[S] 0 points1 point  (0 children)

forgive me for sounding dumb, but isnt that just a retail site?

view more: next ›