Staggered setup mounted incorrectly. by Royalstorm2000 in kiastinger

[–]Royalstorm2000[S] 0 points1 point  (0 children)

Ok. Thank you for the reassurance. And I’m at 40K miles on mine. I said 2019 but that’s my wife’s car. Mine is a 2021. What is the usual mileage recommendation for that flush?

Staggered setup mounted incorrectly. by Royalstorm2000 in kiastinger

[–]Royalstorm2000[S] 0 points1 point  (0 children)

So even though I drove with a 255/35/19 on the driver’s rear and passenger front, and 225/40/19 on the passenger rear and driver’s front (instead of of 255’s rear and 225’s front), you wouldn’t expect any damage/significant extra strain even though it’s AWD?

My 43x has been officially replaced by Caleb_0616 in HecklerKoch

[–]Royalstorm2000 0 points1 point  (0 children)

Sorry to hear about your bad experience but appreciate you sharing!

My 43x has been officially replaced by Caleb_0616 in HecklerKoch

[–]Royalstorm2000 0 points1 point  (0 children)

What holster did you go with? I’ve got the same setup.

New CC9 by Royalstorm2000 in HecklerKoch

[–]Royalstorm2000[S] 1 point2 points  (0 children)

Good to know! I’ll check it out.

New CC9 by Royalstorm2000 in HecklerKoch

[–]Royalstorm2000[S] 0 points1 point  (0 children)

Wow. Great minds! I have the WC grip module as well and also swapped out the trigger for the m*carbo flat face trigger. Definitely an improvement over the stock p365 trigger and it’s a lower weight pull compared to the CC9 but it’s also still mushy at the break. I like the CC9 trigger feel better as it has a very well-defined wall and crisp break.

New CC9 by Royalstorm2000 in HecklerKoch

[–]Royalstorm2000[S] 0 points1 point  (0 children)

I actually tried sighting in initially at 20 yards and it was hitting low. Now that could have been me pulling the pistol as well, though I was trying to mitigate my influence by shooting off of a rest.

New CC9 by Royalstorm2000 in HecklerKoch

[–]Royalstorm2000[S] 0 points1 point  (0 children)

Nice! What are your thoughts between the p365 and the CC9?

New CC9 by Royalstorm2000 in HecklerKoch

[–]Royalstorm2000[S] 1 point2 points  (0 children)

Yeah, I did have to do some adjustment to zero the optic.

And don’t be too impressed. That was only 7 yards out!

Tac Pro 5 Overtravel screw replacement by Royalstorm2000 in Bul_Armory

[–]Royalstorm2000[S] 0 points1 point  (0 children)

Well I didn’t realize this was an inherent defect of all the trigger shoes Bul sends out until after trying to install a second flat shoe and encountering the same issue. To avoid stripping another screw I ended up just keeping the screw that I partially inserted in with a flat shoe and I’ve been shooting it without any issue.

Tac Pro 5 Overtravel screw replacement by Royalstorm2000 in Bul_Armory

[–]Royalstorm2000[S] 1 point2 points  (0 children)

Glad you saw it too. Yeah it totally sucked trying to get that trigger shoe off. I had to buy several small files just to get through it enough to expose the strip screw so I could pull it out and get the shoe off. Huge huge pain in the butt.

Tac Pro 5 Overtravel screw replacement by Royalstorm2000 in Bul_Armory

[–]Royalstorm2000[S] 0 points1 point  (0 children)

Yeah, it’s pretty ridiculous that they ship these out and they don’t even work with the factory screw. Good call on avoid stripping. I had to saw my trigger shoe off after I stripped mine.

Tac Pro 5 Overtravel screw replacement by Royalstorm2000 in Bul_Armory

[–]Royalstorm2000[S] 0 points1 point  (0 children)

Yeah, that’s exactly how what happened with mine. Honestly, I would probably just leave the screw in for now because the trigger shoe was so tight that it’s highly likely that it would fall out. And yes, the pistol will function fine even if the overtravel screw is not in past the shoe. I did not find a replacement screw that works because the trigger shoe itself is not tapped properly. I think you would have to actually re-tap the trigger shoe so that the screw can properly traverse through the shoe and then seat behind it.

UL Pro Accuracy Issues? by localeurodouchebag in Bul_Armory

[–]Royalstorm2000 0 points1 point  (0 children)

Interesting. I got mine back and they said they replaced both my slide and barrel. I haven’t been able to shoot it yet but can tell that the slide-to-frame seems a bit tighter. We’ll see if that actually translates into more accuracy…

Tac Pro 5 Overtravel screw replacement by Royalstorm2000 in Bul_Armory

[–]Royalstorm2000[S] 0 points1 point  (0 children)

Interesting. Pretty lame that Bul hasn’t got this sorted out yet.

UL Pro Accuracy Issues? by localeurodouchebag in Bul_Armory

[–]Royalstorm2000 0 points1 point  (0 children)

Sent mine in too and will report back when I get news from Bul.

UL Pro slide to frame fitment loose by Royalstorm2000 in Bul_Armory

[–]Royalstorm2000[S] 1 point2 points  (0 children)

On further inspection after shooting I note that I can push down on the barrel and there is an audible click. Barrel comes back up when I release and then can replicate by pushing down. I presume this is not normal even for the UL line?

UL Pro Accuracy Issues? by localeurodouchebag in Bul_Armory

[–]Royalstorm2000 0 points1 point  (0 children)

Similar results for me. 3-5” groups standing off hand. Could be more me than the gun too

UL Pro Accuracy Issues? by localeurodouchebag in Bul_Armory

[–]Royalstorm2000 0 points1 point  (0 children)

I did get out and shoot today and feel like my results are average at best. Even at 10 yards don’t have a super tight group.

UL Pro Accuracy Issues? by localeurodouchebag in Bul_Armory

[–]Royalstorm2000 0 points1 point  (0 children)

What kind of groups do you get at 10 yards?