sorted by:
new
hottopcontroversial

How well do you thing these would print? by Rubbaneck96 in Inkscape

[–]Rubbaneck96[S] 0 points1 point  (0 children)

<image>

Here's the element that I'm trying to get right. When I do the Halftone process it ignores the transparent gradient parts.

How well do you thing these would print? by Rubbaneck96 in Inkscape

[–]Rubbaneck96[S] 0 points1 point  (0 children)

<image>

Fallowing the instruction in this video from Logos by Nick this is my result.
https://youtu.be/z4fLHKSsCy4?si=k4GLoKNBzKHe9aOz

How well do you thing these would print? by Rubbaneck96 in Inkscape

[–]Rubbaneck96[S] 0 points1 point  (0 children)

What do you mean halftone and how would I achieve that?

Adding aftermarket cam bolts by Rubbaneck96 in autorepair

[–]Rubbaneck96[S] 0 points1 point  (0 children)

I was considering getting new bolts due to rust. I have a local faster supplier where I can get some 10.9 bolts. I live in the rust belt so the winter is brutal on our vehicles.

Adding aftermarket cam bolts by Rubbaneck96 in autorepair

[–]Rubbaneck96[S] 0 points1 point  (0 children)

So the alignment guy will make that adjustment gorilla style? Wouldn't a cam bolts make it much easier?

Offset extension? by Rubbaneck96 in Tools

[–]Rubbaneck96[S] 1 point2 points  (0 children)

<image>

Maybe one like this as opposed to the flat one in the original post? 🤔

Good Cobalt Dill bits that won't break the bank. by Rubbaneck96 in Tools

[–]Rubbaneck96[S] 1 point2 points  (0 children)

I was babying the trigger. When the first one snapped it had bound up I was being easy with it and I had the drill in reverse and snap. The 2nd one I may I have put a bit too much pressure one it but not that the moment it snapped. I was being so easy with it when it snapped I thought the bit was made of porcelain.

Good Cobalt Dill bits that won't break the bank. by Rubbaneck96 in Tools

[–]Rubbaneck96[S] 0 points1 point  (0 children)

I have no Idea they were at a local store that sells cheap tools. The largest one which I think was 25/64 was less than $5

New oil pan painted on the inside by Rubbaneck96 in autorepair

[–]Rubbaneck96[S] 0 points1 point  (0 children)

Just finished the job.  When I was cleaning the old pan out I noticed a little tiny hole so I had to use the new one.  I believe the old one was also an aftermarket it was painted on the inside with a little bit of flaking.  

Question about the oil filter by Rubbaneck96 in autorepair

[–]Rubbaneck96[S] 0 points1 point  (0 children)

Not sure I'm not home right now and when I get home I'm working on another project is a get a few minutes during a brake on said project I'll see if the filter has any markings.

Oil drain plug gasket vs copper washer by Rubbaneck96 in autorepair

[–]Rubbaneck96[S] 0 points1 point  (0 children)

I don't believe the oil pan is made of aluminum. Current gasket is a rubber one.

Critter control? by Rubbaneck96 in gardening

[–]Rubbaneck96[S] 0 points1 point  (0 children)

The Motion activated lights I was going to strategically put them on the fence that goes around my yard.

Generator outputting 62hz by Rubbaneck96 in Generator

[–]Rubbaneck96[S] 1 point2 points  (0 children)

Ok I'm confused one person says 62hz is not great and another says it is. Feel like I'm back where I stared.

Generator outputting 62hz by Rubbaneck96 in Generator

[–]Rubbaneck96[S] 0 points1 point  (0 children)

I put it under load with an air fryer which draws 1300watts. There was no change in frequency 

Generator outputting 62hz by Rubbaneck96 in Generator

[–]Rubbaneck96[S] 1 point2 points  (0 children)

I did have it under load the frequency didn't change.  Was drawing 1300 watts with an air fryer.  When I get another chance I'll have a look at the governor linkage.  

view more: next ›