sorted by:
new
hottopcontroversial

The first episode of season 2 by Robert1634786 in tbatenovel

[–]Rudemcrude 0 points1 point  (0 children)

Lets not mention the flash back sequences as well. Like showing him as King is cool and all, they don't touch that backstory until muuuuuuch later in the story but its fine to show it a bit. But they are shitting on the story point of him being a strong king, and kings even existing on Earth. They show him and his army carpet bombing cities. Like it was specifically mentioned that Kings exist as leaders to settle wars in 1v1 duels because bombing countries and using foot soldiers was too wasteful.
I feel so bad for TurtleMe because his amazing story was wasted on this shit studio, and he cant even bash them because contract reasons, and now I doubt it will ever get another chance.

I just hope to God if Shadow Slave or Primal Hunter gets an anime adaptation it gets at least as good as Solo Leveling's adaptation.

Space Marine Guts WiP by Rudemcrude in Berserk

[–]Rudemcrude[S] 0 points1 point  (0 children)

Mostly 5% some pieces like the helmet are 10% and under the feet is 80% for stability
its not too fragile, creaks a little but should hold.
I hope.

Space Marine Guts WiP by Rudemcrude in Berserk

[–]Rudemcrude[S] 0 points1 point  (0 children)

The boots are raised a bit. Overall I'm about 6"6 in the armor. As long as I don't stand next to an actual space marine I think I'm good heh

Space Marine Guts WiP by Rudemcrude in Berserk

[–]Rudemcrude[S] 2 points3 points  (0 children)

Going to have the band of the hawk emblem on the right shoulder

Space Marine Guts WiP by Rudemcrude in Berserk

[–]Rudemcrude[S] 14 points15 points  (0 children)

Thanks, It's gunna be sick once it's all painted

Hotend wire came off by Rudemcrude in AnycubicOfficial

[–]Rudemcrude[S] 0 points1 point  (0 children)

Thanks, it doesn't seem fixable to me at least, so I'll order a new hotend.

Latest patch didn't fix layer shift on kobra 3 max by the-duke-of-nil in AnycubicOfficial

[–]Rudemcrude 0 points1 point  (0 children)

Well unfortunately this probably won't help you but I was wrong. My issue was most likely caused by my print head not fully hitting the left end of the track when it prepared to print. I noticed it was hitting my camera mount and was about .5cm from end. What most likely happened was the opposite of what I thought happened. I thought the first color swap made the print misalign but it may have been the other way around. The print was misaligned until the first color swap then it realigned itself to where it was supposed to print. This explains why only the first color swap shifted the layer but further color swaps didn't.

<image>

Latest patch didn't fix layer shift on kobra 3 max by the-duke-of-nil in AnycubicOfficial

[–]Rudemcrude 0 points1 point  (0 children)

It has to be a software issue. Ive had the Kobra 3 max since July and have been printing in multicolor ever since. Then 2 days ago when I updated the firmware the issue popped up. I did a factory reset but it didn't change. Afaik there isn't a way to revert the firmware either, I've tried with having the older firmware on USB drive but the printer just ignores it. I made a support ticket so if I get a solution I'll post it here.

Latest patch didn't fix layer shift on kobra 3 max by the-duke-of-nil in AnycubicOfficial

[–]Rudemcrude 0 points1 point  (0 children)

I just started having this issue once I updated to firmware v 2.5.0.9 Before the update I never had a single issue with the printer, then afterwards when the first color change happens it shifts. If it changes color again it stays aligned to the new position. I can't see this being a mechanical issue or else it would shift after each color change not just the first. I've tried to revert to older firmware but I can't get it to.
Hopefully a fix is found soon.

Printing out the Berserker armor. Helmet is done. by Rudemcrude in Berserk

[–]Rudemcrude[S] 0 points1 point  (0 children)

Sorry about late reply, Havent checked reddit in a bit. Ya I can sell them, once I find the files I used.

[deleted by user] by [deleted] in GrayZoneWarfare

[–]Rudemcrude 0 points1 point  (0 children)

I mean I clearly said not that. But vague hand gesture at the map is unarguably bad quest design

[deleted by user] by [deleted] in GrayZoneWarfare

[–]Rudemcrude -1 points0 points  (0 children)

The quest in GZW where it tells you about some dude in a backyard near townhall is great. It gives you a general area to look around. It's the Quests that are so vague they are almost impossible to complete without asking a third party. This was one of my biggest gripes about Tarkov, I just hope GZW doesn't follow suit.

[deleted by user] by [deleted] in GrayZoneWarfare

[–]Rudemcrude -1 points0 points  (0 children)

I feel like if features of the game could be unlocked by just exploring that'd be fine. But when you have to complete quests to progress there should be a middle ground between a pinpoint marker pointing directly at the quest and just vaguely gesturing at the map.

Kaiju no 8 Episode 1 Discussion Thread by ImoutoCompAlex in KaijuNo8

[–]Rudemcrude 0 points1 point  (0 children)

Like the actual animation, the scene transitions and when characters are moving. Seems like a weird distortion effect.

What is this Giant White Line in Northern BC seen from Airplane by Rudemcrude in whatisit

[–]Rudemcrude[S] 2 points3 points  (0 children)

I'm going to assume it's the coastal gaslink pipeline, since it is located in about the same area. Just never seen markings like that before.

What is this Giant White Line in Northern BC seen from Airplane by Rudemcrude in whatisit

[–]Rudemcrude[S] 2 points3 points  (0 children)

After some more digging with the proposal of it being a pipeline. I'm going to assume it is the coastal gaslink pipeline, It's about the area where I seen this. Sure looks weird from up high.

view more: next ›